GE GTW750CSLWS - Smart Dispense; Bulk Smart Dispenser

– 13 –
(Continued next page)
E
3UHWUHDWLQJRU6RDNLQJ8VLQJWater Station (on some models)
This feature is for the pretreating
of garments only and not intended
to serve as an actual wash cycle.
When selected, the washer will
supply either fresh water or wa-
ter mixed with detergent from the
SmartDispense system for gar-
ment hand pre-washing or pre-
treating use.
The pretreating water will be
dispensed from the area located
in the back of the main opening of
the washer. When selected, any
water dispensed into the wash tub
during the pretreat will be drained
from the machine before any sub-
sequently selected wash cycle can
begin.
:DWHU6WDWLRQ2QO\6HOHFWWKLVIHDWXUH
1. Rotate the cycle selection knob to Water Sta-
tion.
2. Push the Select button until the LED below
Water is illuminated.
3. Select the desired water temperature using
the Temp button.
4. Press the Start button to initiate the feature. If
the lid is not already open, raise the lid of the
ZDVKHUWRVWDUWWKHÀRZRIIUHVKZDWHUIURP
the dispensing area. Water will continue to be
dispensed until the lid is closed or the water
level in the tub reaches the maximum level.
If the lid is closed before the maximum level in
the tub is reached, additional water can be dis-
pensed by opening the lid again. Once the lid
is closed, water dispensed using the water on
demand feature will remain in the tub until the
cycle selection knob is rotated to an actual wash
cycle, or the Start button is held in for 3 seconds,
at which point the water in the tub will be drained
out of the machine.
If the lid is not closed, the water in the tub will
automatically be drained after 15 minutes. With
the lid closed, if the cycle selection knob is not ro-
tated to an actual wash cycle, or the Start button
is not held in for 3 seconds, the water in the tub
will automatically be drained after 24 hours.
:DWHU6WDWLRQZLWK'HWHUJHQW6HOHFWWKLVIHD-
ture:
1. Rotating the cycle selection knob to the Water
Station.
2. Push the Select button until the LED below
Detergent + Water is illuminated.
3. Select the desired water temperature using
the Temp button.
4. Press the Start button to initiate the detergent
feature. If the lid is not already open, raise
WKHOLGRIWKHZDVKHUWRVWDUWWKHÀRZRIVRDS\
water from the dispensing area. Soapy water
will continue to be dispensed until the lid is
closed or the water level in the tub reaches
the maximum level.
Alternatively, use this feature to
soak garments in the pretreated
water for up to 24 hours with the lid
closed and the cycle knob remain-
ing on Water Station.
In order to use this feature to soak,
keep the dial on Water Station and
close the lid. Soak can be left for up
to 24 hours before the water in the
tub will be automatically drained.
Rotating the dial, holding the Start
button for 3 seconds or leaving the
lid open for more than 15 minutes
will all automatically drain the water
from the tub.
If the lid is closed before the maximum level in the
tub is reached, additional soapy water can be dis-
pensed by simply opening the lid again. Once the
lid is closed, soapy water dispensed will remain in
the tub until the cycle selection knob is rotated to
an actual wash cycle, or the Start button is held in
for 3 seconds, at which point the soapy water in
the tub will be drained out of the machine.
If the lid is not closed, the soapy water in the tub
will automatically be drained after 15 minutes.
With the lid closed, if the cycle selection knob is
not rotated to an actual wash cycle, or the Start
button is not held in for 3 seconds, the soapy
water in the tub will automatically be drained after
24 hours.