What to do if I run out of conditioned water between regenerations with my GE Pro Elite 268-716-150-1248?
If you run out of conditioned water between regenerations with your GE Water Filtration Systems, it could be due to: * Improper regeneration: Repeat the regeneration process. * Incorrect resin volume setting: Reset the control and program the resin volume to the correct setting.
Why GE Water Filtration System control will not draw regenerant?
If your GE Water Filtration System isn't drawing regenerant, several factors could be at play: * Low water pressure: Make sure the pressure is correctly set according to the instructions. * Restricted drain line: Remove any obstructions in the drain line. * Plugged injector: Clean the injector and screen. * Valve disc issues: Remove any foreign matter from the disc and check if the disc closes properly by pushing the stem. * Prematurely closed air check valve: Momentarily put the control into brine refill.
What to do if I notice hard water leakage after regeneration in my GE Pro Elite 268-716-150-1248 Water Filtration Systems?
If you experience hard water leakage after regeneration with your GE Water Filtration Systems, it could be due to: * Improper regeneration: Repeat the regeneration process, ensuring the correct regenerant dosage is set. * Damaged O-ring: Replace the O-ring around the riser pipe. * Incorrect resin volume setting: Reset the control and program the resin volume to the correct setting.
Why GE Water Filtration System control will not regenerate automatically?
If your GE Water Filtration System control will not regenerate automatically, check the following: * AC adapter or motor connection: Ensure the power is connected. * Defective motor.
What causes flowing or dripping water at drain or regenerant line after regeneration in GE Water Filtration Systems?
If you observe flowing or dripping water at the drain or regenerant line after regeneration in your GE Water Filtration Systems, it could be due to: * Debris preventing valve disc closure: Remove any debris.
What causes GE Pro Elite 268-716-150-1248 to backwash or purge at an excessively low or high rate?
If the GE Water Filtration System backwashes or purges at an excessively low or high rate, it may be due to foreign matter affecting valve operation. Remove the drain controller and clean the ball and seat.
Why is the regenerant draw intermittent or irregular in my GE Water Filtration Systems?
If you experience intermittent or irregular regenerant draw with your GE Water Filtration Systems, it could be due to low water pressure. Set the pump to maintain 20 psi at the conditioner.
Why there is no conditioned water after regeneration in GE Pro Elite 268-716-150-1248?
If there is no conditioned water after regeneration in your GE Water Filtration System, it might be due to: * No regenerant in the regenerant tank: Add regenerant to the tank.
What does ERR 3 mean on my GE Pro Elite 268-716-150-1248 and how to fix it?
If the GE Water Filtration System displays ERR 3, the control may not know the position of the camshaft. Allow two minutes for the control to return to the Home position. The hourglass should flash on the display, indicating the motor is running. If the camshaft isn't turning, check the motor connection, wire harness, optical sensor, and motor gear engagement. If the camshaft turns for more than five minutes, verify the optical sensor, camshaft connection, and check for obstructions in the cam slots.
What does ERR 1 mean on my GE Pro Elite 268-716-150-1248 and how to resolve it?
If the GE Water Filtration System displays ERR 1, the program settings have been corrupted. Press any key and reprogram Level I settings.
General| Brand | GE |
|---|---|
| Filter Type | Carbon Block |
| Filter Life (Months) | 6 |
| NSF Certified | Yes |
| Model | 268-716-150-1248 |
| NSF Standards | 42 |
| Product Type | Under Sink Water Filtration System |
Crucial safety precautions and warnings for installation and operation of the water conditioning system.
Instructions for connecting the water lines and installing the bypass valve system.
Information on AC adapters, power supply requirements, and potential power interruption effects on settings.
Explains how the system operates, including water flow during service and regeneration cycles.
Outlines the steps for programming the control for normal applications, including key settings.
Details on adjusting Level II parameters for fine-tuning conditioner operation.
Steps for starting the 268 water conditioning system, filling the brine tank last.
Steps for starting the 268r water conditioning system, filling the brine tank first.
Lists common error codes for the Analyzer control and their corresponding causes and solutions.
Provides solutions for common system problems like regenerant tank overflow and water leakage.
To Next Page
