GE VH Series 1500 User Manual

GE
Consumer & Industrial
User manual
Digital Energy™ Uninterruptible Power Supply
On-line VH Series UPS
700 - 1000 - 1500 - 2000 - 3000 VA
GE Consumer & Industrial SA
General Electric Company
CH – 6595 Riazzino (Locarno
Switzerland
T +41 (0)91 / 850 51 51
F +41 (0)91 / 850 51 44
www.gedigitalenergy.com

GE VH Series 1500 Specifications

General

Brand	GE
Model	VH Series 1500
Category	UPS
Language	English

Summary

Important Safety Instructions

Save These Instructions

Instructions for installation and maintenance. Keep manual for future reference.

Safety Rules

CAUTION! RISK OF ELECTRIC SHOCK. Do not open unit. Service by qualified personnel only.

Introduction

Introduction

GE Digital Energy VH Series UPS protects equipment from power interference and failures.

Intended Use

UPS protects sensitive electronic equipment like computers and telecommunications.

Transport / Storage

Store UPS in dry location, fully charged. Temperature range -20 to +45°C.

Warranty

36-month warranty against defects in materials and workmanship.

Installation

Package Contents

List of items included: UPS, support parts, mounting set, cables, CD, manual.

Installation Rules

Use grounded outlet, avoid humidity, ensure ventilation, do not plug non-electronic loads.

Installation Procedure

Steps for vertical installation: attach supports, connect DC, assemble front panel.

Vertical Installation - Preparations

Steps to prepare the UPS for vertical tower installation.

Rackmount Installation - Preparations

Steps for rackmount installation: re-position panel, attach brackets, connect DC.

Rear Panel

Identifies input/output sockets, breaker, DC connector, fans, USB and RJ11 ports.

Installation of a Battery Extension Pack

Procedure to connect additional battery packs for extended runtime.

Connecting Interface Devices

Connect USB or RJ11 ports for communication with computer/network.

Connecting Power and Load

Steps to connect UPS to mains power and connect equipment to UPS outputs.

Operation

Operating Panel

Explanation of front panel switches and LEDs for UPS status and control.

Start-up

Procedures for starting the UPS with mains available or unavailable.

Start-up, Mains Available

Steps to start the UPS via front panel or software when mains power is present.

Start-up, Mains Not Available

Procedure to start the UPS using battery power when mains is absent.

Use: Normal Operation

Conditions for normal operation: mains present, UPS on, load within capacity.

Normal Operation Conditions

Mains supply present, UPS on, load within capacity, temperature below alarm.

No-load Shutdown

UPS switches off during mains failure if load < 5% to save battery.

Switching Off

How to switch off the UPS via front panel or software.

Use: Status and Alarm Indications

Table detailing status and alarm indications on the front panel LEDs.

Standby

UPS output is off, batteries are charging.

Normal Operation

Indicates normal operation, referencing section 4.3.1.

On Bypass

Load transferred to mains due to overload or overtemperature.

On Battery

UPS uses battery power due to mains failure.

Battery Low (End of Runtime)

Indicates low battery runtime (less than 2 minutes), requiring immediate action.

Bypass Out of Limits

Mains voltage/frequency outside bypass tolerance, output may be lost.

Overload

Load exceeds UPS capacity, may lead to bypass or shutdown.

Replace Battery

Indicates battery is worn out or wiring is faulty. Replace battery.

General Alarm

Indicates various faults; buzzer behavior specifies the alarm type.

Shutdown Pending

UPS is preparing for shutdown via monitoring software.

Startup Pending

UPS is preparing for startup via monitoring software.

P-N (Phase-Neutral) Reversal Indication

Indicates reversed phase and neutral at the UPS input.

Use: Setup Mode

Allows changing output voltage, bypass, P-N indication, and output frequency.

Battery Management

Features for battery life and reliability: quick, automatic, manual, deep battery tests.

Communication

USB Port

USB port for advanced communication with UPS software.

RJ 11 Port

RJ 11 port for contact interface, signals mains failure, alarm, battery low.

USB / RS232 / Relay Interface Card (Option)

Optional card with USB, RS232, and relay contacts for alarms.

Option: Extended Runtime (VH Series 1000-3000)

Maintenance

Safety

DANGER: High voltages present. Only authorized personnel may remove cover.

General

UPS is virtually maintenance free; keep clean and ensure ventilation.

Recycling the UPS at the End of Service Life

Proper disposal and recycling of UPS and batteries according to local regulations.

Batteries

Information on battery service life, testing, and replacement.

General

Battery service life is 3-6 years. Automatic quick battery test ensures operation.

Battery Replacement

Step-by-step guide for replacing the UPS batteries.

Troubleshooting

Specifications