L
Lisa RamirezAug 14, 2025
What to do if the input circuit breaker tripped on my GE UPS?
- MMichelle McfarlandAug 14, 2025
If the input circuit breaker tripped, it is likely due to a GE UPS overload. Reduce the load and reset the breaker.
To Next PageTo Next PageWhat to do if the input circuit breaker tripped on my GE UPS?
If the input circuit breaker tripped, it is likely due to a GE UPS overload. Reduce the load and reset the breaker.
What to do if my GE UPS is overloaded?
If the 'Overload' LED is lit and the buzzer sounds continuously, it means your GE UPS is overloaded. To resolve this, reduce the load by unplugging non-critical devices.
Why is my GE 1000-1500-2000-3000 VA UPS beeping continuously due to over-temperature?
If your GE UPS buzzer sounds continuously, it may be due to over-temperature caused by high ambient temperature or blocked ventilation. Try reducing the ambient temperature and enhancing ventilation. It can also be a sign of fan failure, in which case you should have the fan replaced.
What to do if my GE 1000-1500-2000-3000 VA UPS has no output?
Your GE UPS might have no output due to several reasons: * The UPS might be over-temperature, so allow it to cool down. * There could be a utility failure and the battery is depleted, in this case wait until utility power returns. * The input breaker might have tripped, refer to the troubleshooting steps for a tripped input breaker.
Why won't my GE 1000-1500-2000-3000 VA UPS switch on?
Your GE UPS may not switch on for several reasons: * The line cord might not be connected, so ensure it is properly connected. * The wall socket outlet might be dead, or the mains voltage is out of limits, in this case contact a qualified electrician. * The input circuit breaker might be tripped, or the battery voltage is too low, check whether the UPS is not overloaded, reset the breaker and allow the UPS to recharge the battery.
What does it mean when the 'Replace battery' LED is on and the buzzer sounds continuously on my GE 1000-1500-2000-3000 VA?
If the 'Replace battery' LED is lit and the buzzer sounds continuously, it could mean one of two things: 1. It might be a 'false alarm' triggered by a battery test just after a utility failure. In this case, allow the UPS to recharge the battery for approximately 8 hours, then repeat the battery test. 2. The battery might be close to being worn out. Allow the UPS to recharge for about 8 hours and then perform a battery test again. If the alarm persists, consider replacing the battery.
What should I do if the 'Battery low' LED lights up and the buzzer beeps on my GE 1000-1500-2000-3000 VA UPS?
If the 'Battery low' LED lights up and the buzzer beeps 2x/sec, it means the battery is close to being exhausted during a utility failure. The UPS output will be lost soon, so shut down the load in an orderly manner.
How to fix GE 1000-1500-2000-3000 VA UPS if it cannot be linked to computer?
If your GE UPS cannot be linked to a computer, it could be due to: * A defective communication cable. Check the cable. * A transmitting rate fault. Adjust the transmitting rate. * A communication port fault. Check the COM1/COM2 configuration of the computer.
What does it mean when the 'Fault' LED flashes on my GE 1000-1500-2000-3000 VA UPS?
If the 'Fault' LED is flashing, it indicates a wiring fault (L-N reversed). Have the site wiring checked by a qualified electrician.
General| Form Factor | Tower |
|---|---|
| Frequency | 50/60 Hz |
| Humidity | 0-95% non-condensing |
| Dimensions | Varies by model |
| Weight | Varies by model |
| Apparent Power | 1000 VA / 1500 VA / 2000 VA / 3000 VA |
| Topology | Line Interactive |
| Battery Type | Sealed Lead Acid |
| Communication Interface | USB |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -15°C to 45°C |
Provides general safety precautions for UPS operation and installation.
Details safety requirements for installing the UPS unit.
Covers precautions and guidelines for handling UPS batteries.
Guidelines for safely transporting and storing the UPS unit.
Lists the items included in the UPS packing box.
Provides guidance on selecting an appropriate location for the UPS.
Details the connectors and components on the rear panel of the UPS.
Step-by-step guide for installing the UPS and connecting it to power.
Describes the front panel controls and indicators of the UPS.
Instructions for starting up the UPS under different power conditions.
Details normal operating conditions and indicators for the UPS.
Explains how the UPS behaves during abnormal conditions.
Overview of the UPS communication interface and its capabilities.
Details the RS232 serial communication port and its pin assignments.
Explains the dry contact interface for alarms and remote control.
Information on the optional SNMP card for network monitoring.
How to increase UPS runtime using external battery modules.
Details the optional TVSS for surge protection on communication lines.
Overview of general maintenance requirements for the UPS.
Information on battery lifespan and the importance of regular testing.
Safety warnings and procedures for replacing UPS batteries.
Guidelines for environmentally responsible recycling of the UPS.
A guide to diagnosing and resolving common UPS problems.
Detailed technical specifications for the Digital Energy GT Series UPS models.
