DesignedandmanufacturedbyGEMINITECHNOLOGIESsrl‐ViaL.Galvani,12
21020BodioLomnago(VA)
Italy
Tel.+390332943211–Fax+390332948080–www.gemini‐alarm.com
ISO9001CERTIFIEDCOMPANY
AC2955Rev.0001/2018
2/4
3.1 COMPLETE SYSTEM ARMING
Press the lock button on the vehicle remote control or button “1” on the Gemini remote control (P/N 738W); system arming is confirmed by a siren chirp and a flash
of the turn indicators (if optical/acoustic signals are enabled). The system has a 30 sec. arming delay during which the LED is ON steady.
3.2 SYSTEM ARMING WITH SENSORS EXCLUSION
To arm the system without arming interior protection press button “3” on the Gemini remote control. System arming is confirmed by a quick low-pitched chirp and a
flash of the turn indicators (if signals are enabled).
Sensors can be excluded via the vehicle original remote control on the following vehicles:
• FIAT DUCATO ‘11›
• FORD TRANSIT ‘14›
• RENAULT MASTER ‘10›
To exclude interior protection via the vehicle original remote control, proceed as follows:
• Lock the vehicle via the vehicle original remote control.
• Wait at least 5 sec., but before the end of the arming delay, and press the lock button again.
• Exclusion is confirmed by 1 low-pitched chirp.
NB: THIS CONFIRMATION TONE CANNOT BE EXCLUDED.
Exclusion of sensors is bound to each single arming cycle. They will be reset upon next arming.
3.3 PASSIVE ARMING
If programmed for passive arming, the system will automatically arm approximately 60 sec. after ignition is switched OFF and the last door is opened and closed.
Arming is confirmed by a siren chirp and a flash of the turn indicators (if signals are enabled).
If programmed for passive arming, interior protection is excluded. Opening a door during the 60-second passive arming countdown will cause the
procedure to interrupt; it will resume once the door is closed.
3.4 ARMING DELAY
There is a 30 sec. delay from the time the system is armed to allow you to leave the vehicle without triggering an alarm: it will be signaled by the LED turned ON
steady.
3.5 SYSTEM ARMED
After the arming delay the system is fully armed and ready to detect any alarm event. The LED will start flashing to confirm the armed status.
3.6 ALARM, NEUTRAL TIME BETWEEN ALARMS AND ALARM CYCLES
Alarm events are signaled by optical/acoustic signals. Once the alarm ceases, there is a 5 sec. time-interval before another alarm can be triggered. Each alarm
event can generate up to 10 cycles for each input and for each arming cycle. One alarm cycle lasts for 30 sec.
3.7 SYSTEM DISARMING
Press the unlock button on the vehicle original remote control or button “2” on the Gemini remote control (P/N 738W); system disarming is confirmed by 2 siren
chirps and 2 flashes of the turn indicators (if signals are enabled).
If an alarm event has occurred while you were away from your vehicle, it will be signaled, when you disarm the sytem, by 5 siren chirps and 5 flashes of the turn
indicators. Alarm causes and relative LED signals are listed in the next paragraph.
3.7 ALARM MEMORY
The LED memory allows to identify the last alarm event signaled by 5 siren chirps and 5 turn indicator flashes when the system is disarmed.
Turn ignition key “ON” and count the number of flashes. The status LED will flash according to the last alarm detected prior to disarming (see table below).
The flash sequence is repeated 3 times; to interrupt turn ignition key “OFF”.
LED FLASHES ALARM CAUSES ALARM CYCLES
Ignition attempt (+15/54)
10
Door tamper
10
Bonnet tamper
10
Boot tamper
10
Volumetric or external sensor
10
Wireless magnetic contacts or opening detectors
10
Wireless infrared sensors (PIR)
10
Wire tampering
10
LED OFF (2 seconds) LED ON (1 second)
3.0 - OPERATING INSTRUCTIONS
To Next Page
Loading...
Need help?
General
