Gemini GEM-P3200 - User Manual

R
PROGRAMMING
INSTRUCTIONS
HARDWIRE WIRELESS
GEM-P3200
CONTROL PANEL/COMMUNICATOR
WI818D 8/00© Napco 2000
Quick Start:
1. Refer to the wiring diagram, connect the keypad(s), siren, aux. power, aux. output, remote bus, earth ground, zone and telephone
wiring. NOTE: See Installation Instructions (WI817).
2. Connect AC power first and then the battery.
3. Configure the keypad (see page 63).
4. Access the Easy Menu Driven (Dealer Program) Mode:
Press
EEEEEE A
Press
g
Until “
ACTIVATE PROGRAM Y/N
” (GEM-RP1CAe2), “
TURNON PROG Y/N
” (GEM-RP2ASe2) or
“17”
(GEM-RP3DGTL) appears on the keypad display.
Press
F
To Enter Dealer Program Mode (see page 6).
Master Security Code
(on microshield)
R
COMPUTERIZED SECURITY SYSTEM
ARMED
STATUS
SYSTEM ARMED
01/01/97 12:00AM
12
4
3
56
7890
A
B
C
D
E
F
G
NEXT/YES
PRIOR/NO
AREA
GEMINI
ENT A1
48
INTERIOR
BYPASS FIRE/TBL SYS TBL CHIME
GEM-RP2ASe2
R
COMPUTERIZED SECURITY SYSTEM
ARMED
STATUS
SYSTEM ARMED
01/01/97 12:00AM
12
4
3
56
7890
A
B
C
D
E
F
G
NEXT/YES
PRIOR/NO
AREA
GEMINI
READY
AC ON
READY
AC ON
GEM-RP1CAe2
R
COMPUTERIZED SECURITY SYSTEM
GEMINI
ARMED
STATUS
SYSTEM ARMED
01/01/97 12:00AM
12
4
3
56
7890
A
B
C
D
E
F
G
NEXT/YES
PRIOR/NO
AREA
SYSTEM ARMED
01/01/00 12:00 AM
GEM-RP3DGTL

Gemini GEM-P3200 Specifications

General

Brand	Gemini
Model	GEM-P3200
Category	Control Panel
Language	English

Summary

System Programming Options

Programming Methods Overview

GEM-RP1 CAe2 Keypad Programming

Zone and Central Station Configuration

Setting up zones, fire zones, and central station parameters using the GEM-RP1CAe2 keypad.

User Code Management

Entering and managing user codes, options, authority levels, and access control.

RF Transmitter and Key Fob Configuration

Setting up RF transmitters and key fobs, including zone mapping and assignment.

GEM-RP2 ASe2 Keypad Configuration

Zone, Central Station, and User Code Setup

GEM-RP3 DGTL Keypad Configuration

Zone, Central Station, and Dealer Code Setup

RF Transmitter and Key Fob Setup

Direct Address Program Mode

Accessing and Using Direct Address Mode

Steps to enter and use Direct Address Mode for detailed panel programming.

Keypad Commands for Direct Address Mode

System Delays, Timeouts, and Codes

Keypad System Codes

Central Station Reporting Options

CS Reporting Codes Setup

Zone Options Configuration

Zone Options (Addresses 1200-1786)

Detailed configuration of options for each zone, including response times and bypass settings.

System Options

System Options Configuration (Addresses 2415-2419)

User Area Options

User Area Assignment and Data Entry

Assigning users to areas and configuring their specific options via data entry.

EZM Group and Terminal Control

EZM Group Configuration

RF Receivers and Supervisory Timer Options

RF Receiver Configuration

Setting up the number of RF receivers and their types for wireless expansion.

RF Supervisory Timer Setup

User Program Mode

Accessing and Using User Program Mode

Zone Descriptions (GEM-RP1 CAe2 Keypads)

Keypad Configuration Mode

Keypad Installation and Configuration

Guidelines for installing keypads and configuring their specific settings.

GEM-RP2 ASe2 and GEM-RP3 DGTL Keypad Configuration

Configuration steps for GEM-RP2ASe2 and GEM-RP3DGTL keypads via jumpers.

Keypad Programming Modes

Function Mode

Dealer Mode

GEM-P3200 Wiring Diagram

Power Up Sequence and Wiring Details

Correct order for connecting power and detailed wiring instructions with warnings.