BLIZZARD 500-900 C 3 532103 - Rev.B
Translation of the original instructions
ENGLISH
Translation of the original instructions
ENGLISH
DECLARATION OF INCORPORATION FOR PARTLY
COMPLETED MACHINERY
(2006/42/EC ANNEX II P.1, B)
Manufacturer and person authorised to draft the applicable technical documentation
Company name: FAAC S.p.A. Soc. Unipersonale
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
Hereby declares that the partly completed machinery:
Description: Gear motor for sliding gates
Model: BLIZZARD 500 C; BLIZZARD 900 C.
the following essential requirements of the Machinery Directive 2006/42/EC
(including all applicable amendments) have been applied and fulfilled:
1.1.2, 1.1.3, 1.1.5, 1.1.6, 1.2.1, 1.2.3, 1.2.5, 1.2.6, 1.3.1,
1.3.2, 1.3.4, 1.3.6, 1.3.9, 1.4.1, 1.4.2.1, 1.5.1, 1.5.2,
1.5.5, 1.5.6, 1.5.7, 1.5.8, 1.5.10, 1.5.11, 1.6.1, 1.6.4,
1.7.1, 1.7.2, 1.7.3, 1.7.4.2, 1.7.4.3
and that the relevant technical documentation has been compiled in compliance
with part B of Annex VII.
Furthermore, the following harmonised standards have been applied:
EN12100:2010
EN13849-1:2015
EN13849-2:2012
Other applied standards:
EN12453:2000
Undertakes to transmit by mail or by e-mail, in response to a reasoned request by
the national authorities, relevant information on the partly completed machinery.
It is also declared that the partly completed machinery identified above may not be com-
missioned until the final machine - into which it will be incorporated - has been declared
complaint with the provisions of the above mentioned Machine Directive 2006/42/EC.
Bologna, Italy, 30-09-2016 CEO
EU DECLARATION OF CONFORMITY
The Manufacturer
Company name: FAAC S.p.A. Soc. Unipersonale
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
hereby declares under his sole responsibility that the following product:
Description: Gear motor for sliding gates
Model: BLIZZARD 500 C; BLIZZARD 900 C.
Complies with the following relevant Union harmonization legislations:
2014/30/EU
2011/65/EU
Furthermore, the following harmonised standards have been applied:
EN61000-6-2:2005
EN61000-6-3:2007 + A1:2011
Bologna, Italy, 30-09-2016 CEO
CONTENTS
1. INTRODUCTION TO THIS INSTRUCTION MANUAL .......... 4
1.1 Meaning of Symbols Used ....................................... 4
2. SAFETY RECOMMENDATIONS .................................. 5
2.1 Installer safety .................................................... 5
2.2 Transport and storage ............................................ 5
2.3 Unpacking and handling ........................................ 6
2.4 Disposal of the product .......................................... 6
3. BLIZZARD 500-900 C .............................................. 6
3.1 Intended use ...................................................... 6
3.2 Limitations of use ................................................. 6
3.3 Prohibited uses ................................................... 6
3.4 Emergency Use ................................................... 7
3.5 Product Warnings ................................................. 7
3.6 Product Identification ............................................ 7
3.7 Technical Characteristics ......................................... 7
3.8 Component Identification ....................................... 8
3.9 Dimensions ........................................................ 8
4. INSTALLATION REQUIREMENTS ................................ 9
4.1 Mechanical Requirements ....................................... 9
4.2 Electrical System .................................................. 9
4.3 Example System .................................................10
5. INSTALLATION ................................................... 10
5.1 Tools Required ...................................................10
5.2 Installation Dimensions .........................................11
5.3 Base plate .........................................................12
5.4 Fastening the Gear Motor.......................................12
5.5 Manual Operation ...............................................13
5.6 Installing the Rack ...............................................13
5.7 Adjustments and Checks .......................................16
6. ELECTRONIC BOARD ............................................ 17
6.1 Terminal boards and connectors ...............................18
6.2 Photocells and safety devices ..................................19
7. START-UP.......................................................... 20
7.1 Power supply and earthing .....................................20
7.2 LEDs Check .......................................................20
7.3 Installation of the Limit Switches ..............................21
7.4 Programming ....................................................22
7.5 Direction of movement check ..................................24
7.6 Final Operations .................................................24
8. MAINTENANCE ................................................... 25
8.1 Scheduled Maintenance ........................................25
9. OPERATING LOGICS ............................................. 27
10. INSTRUCTIONS FOR USE ..................................... 30
10.1 Safety recommendations......................................30
10.2 Product Warnings ..............................................30
10.3 Emergency Use .................................................30
10.4 Manual Operation .............................................. 30
To Next Page
Loading...
