Gigabyte R282-Z93 User Manual

Electrostatic Discharge (ESD)
CAUTION!
ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU
PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,
PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-
TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER
WHEN HANDLING PARTS.
Always handle boards carefully, they can be extremely sensitive to ESD. Hold boards only by
their edges without touching any components or connectors. After removing a board from its
protective ESD bag or from the system, place the board component side up on a grounded, static
free surface. Use a conductive foam pad if available but not the ESD bag. Do not slide the board
over any surface.
System power on/off: To service components within the server, please ensure the power has
been disconnected.
e.g. Remove the node from the server chassis (to disconnect power) or disconnect the power
from the server chassis.
Make sure the system is removed from the rack before opening the chassis, adding, or removing
any non hot-plug components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be present
on power, telephone, and communication cables. Turn off the system chassis and disconnect the
cables attached to the system before servicing the chassis. Otherwise, personal injury or equip-
ment damage can result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage drives, boards, and
other parts. We recommend that you perform all procedures in this chapter only at an ESD work-
station. If one is not available, provide some ESD protection by wearing an antistatic wrist strap
attached to chassis ground (any unpainted metal surface on the server) when handling parts.
ESD and handling boards: Always handle boards carefully. They can be extremely sensi-tive to
electrostatic discharge (ESD). Hold boards only by their edges. After removing a board from its
protective wrapper or from the system, place the board component side up on a grounded, static
free surface. Use a conductive foam pad if available but not the board wrapper. Do not slide
board over any surface.

Gigabyte R282-Z93 Specifications

General

Processor family	AMD
Processor socket	Socket SP3
Built-in processor	No
Motherboard chipset	-
Compatible processor series	AMD EPYC
Number of processors supported	2
Hot-swap HDD bays	Yes
Storage drive sizes supported	2.5, 3.5 \
Supported storage drive types	HDD & SSD
Number of storage drives supported	12
Supported storage drive interfaces	Serial ATA III
PCI Express x16 slots	6
PCI Express slots version	4.0
PCI Express x8 (Gen 3.x) slots	1
Power supply	2000 W
Input current	10 - 12 A
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
80 PLUS certification	80 PLUS Platinum
Memory channels	Octa-channel
Number of DIMM slots	32
Supported memory types	DDR4-SDRAM
Maximum internal memory	128 GB
Supported RDIMM clock speeds	2933, 3200 MHz
Discrete graphics card model	Not available
On-board graphics card model	Aspeed AST2500
Chassis type	Rack (2U)
Fan diameter	80 mm
Product color	Black
Number of fans	4 fan(s)
LAN controller	Intel® I350-AM2
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Fast Ethernet, Gigabit Ethernet
Sustainability certificates	RoHS
USB 2.0 ports quantity	0
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity	4
Storage temperature (T-T)	-40 - 60 °C
Operating temperature (T-T)	10 - 35 °C
Storage relative humidity (H-H)	20 - 95 %
Operating relative humidity (H-H)	8 - 80 %
Package depth	588 mm
Package width	982 mm
Package height	268 mm
Package weight	25500 g

Weight and Dimensions

Depth	730 mm
Width	438 mm
Height	87 mm
Weight	18500 g