What should I do if no pressure value is displayed, the value is unchanged, or it changes erratically when the cuff is inflated on my Gima CONTEC08A-VET?
Pull out the cuff to deflate. Stop using the device and contact us.
What to do if Gima Measuring Instruments won't start when holding the power button?
If your Gima Measuring Instruments device doesn't start when you hold the power button, it could be due to exhausted batteries or reversed battery polarities. Replace all four batteries with new ones and check the battery installation to ensure proper placement according to the polarities.
What to do if there is no pressure in Gima Measuring Instruments?
If there is no pressure in your Gima Measuring Instruments device, it could be due to a cuff leakage, the cuff windpipe not being correctly connected, or the cuff not being inflated. You may need to buy a new cuff or correctly connect the cuff windpipe with the cuff. If the cuff is not inflated, stop using the device and contact us.
What causes overpressure in Gima Measuring Instruments?
Overpressure in Gima Measuring Instruments can occur if the cuff is blocked or squeezed. To resolve this, ensure the cuff is correctly connected.
What does 'Excessive movement Over range Saturated signal' mean on Gima Measuring Instruments?
This message on your Gima Measuring Instruments indicates that the signal extent is too big because of movement during measurement. Keep your limbs and body still, and then measure again.
What to do if the cuff on my Gima CONTEC08A-VET Pet Care Product starts inflating before pressing the measurement button or never stops inflating?
Pull out the cuff to deflate. Stop using the device and contact us.
What to do if Gima CONTEC08A-VET can't measure when pressing the button?
If your Gima Pet Care Product won't start a measurement when you press the measurement button, try switching the power off and on again and then restart the measurement.
What causes an air pressure error on my Gima Pet Care Product?
An air pressure error on your Gima Pet Care Product can be caused by no deflation, deflation error, or inflation without stopping. Pull out the cuff to deflate, stop using the device and contact us. It may also be caused by other issues, in that case keep your arm and body still, then measure again.
Why are the BP measurement values too high or too low on my Gima CONTEC08A-VET?
If you're getting BP measurement values that are too high or too low on your Gima Pet Care Product, it could be due to a couple of reasons. First, the cuff might not be connected correctly; ensure it's properly connected. Second, moving your limbs during measurement can also cause inaccurate readings; keep still and restart the measurement.
What to do if Gima Measuring Instruments cuff never deflates?
Pull out the cuff to deflate. Stop using the device and contact us.
Steps for installing AA dry batteries, including polarity and battery cover closure.
Instructions for connecting and using the AC adapter with the device.
Details on technical alarms, such as low power, and how they are managed.
Guidelines for correct limb placement and measurement consistency for accurate results.
Steps to start, stop, and confirm a blood pressure measurement using the device.
How to access and view previously recorded blood pressure and pulse rate measurements.
Procedure for clearing all measurement results from the device's memory.
General| Model | CONTEC08A-VET |
|---|---|
| Category | Pet Care Product |
| Measurement Method | Oscillometric |
| Resolution (Blood Pressure) | 1 mmHg |
| Accuracy (Blood Pressure) | ±3 mmHg |
| Overpressure Protection | Yes |
| Product Type | Veterinary Blood Pressure Monitor |
| Accuracy (Temperature) | ±0.2°C |
| Resolution (Temperature) | 0.1°C |
| Memory Function | Yes |
| Auto Power Off | Yes |
| Waterproof | No |
| Applicable object | Dog, cat and other types of animals |
| Battery Type | AA |
| Probe Cover | Not applicable |
| Dimensions | 130mm x 110mm x 80mm |
| Weight | 300 g |
To Next Page
