GME TX677 - Page 22

TX677 Instruction Manual
22
Factory Reset
A factory reset clears any settings you have made to your radio, and restores it to
the default factory settings.
To perform a factory reset, press and hold the Menu and SQL keys simultaneously
while switching the radio on.
SCANNING
Channel scanning allows you to monitor all channels for incoming signals.
Note: While the radio is scanning, the Menu setting key is disabled.
ADDING OR REMOVING CHANNELS
To select channels for scanning:
Press the  or  keys to select the desired channel.
1. If the
TX677 Instrucon Manual
12 June 2018
© 2018 Standard Communicaons Pty Ltd trading as GME. All rights reserved.
21
50157
Content
Factory Reset
A factory reset clears any sengs you have made to your radio, and restores it to the default factory
sengs.
To perform a factory reset, press and hold the Menu and SQL keys simultaneously while switching the
radio on.
Scanning
Channel scanning allows you to monitor all channels for incoming signals.
While the radio is scanning, the Menu seng key is disabled.
Adding or Removing Channels
To select channels for scanning:
Press the or keys to select the desired channel.
1. If the icon is visible, the selected channel is already in the Scan Memory.
Press F followed by SQL to remove the channel from the scan memory. A low beep will
be heard and the
icon will disappear.
2. If the icon is not visible the selected channel is not presently in the
scan memory. Press F followed by SQL to add the channel to the scan memory.
Scanning for Channels
1. To scan for channels, briey press F followed by the key. The icon will ash and the
channel numbers will change as the radio scans through the channels.
2. To change the scan direcon while scanning, briey press the or keys.
3. To stop scanning, briey press F followed by the key. The icon will stop ashing and
the radio will return to normal operaon.
There must be at least 2 channels stored in the scan memory. If not, the radio will not scan.
icon is visible, the selected channel is already in the Scan
Memory.
Press F followed by SQL to remove the channel from the scan
memory. A low beep will be heard and the
TX677 Instrucon Manual
12 June 2018
© 2018 Standard Communicaons Pty Ltd trading as GME. All rights reserved.
21
50157
Content
Factory Reset
A factory reset clears any sengs you have made to your radio, and restores it to the default factory
sengs.
To perform a factory reset, press and hold the Menu and SQL keys simultaneously while switching the
radio on.
Scanning
Channel scanning allows you to monitor all channels for incoming signals.
While the radio is scanning, the Menu seng key is disabled.
Adding or Removing Channels
To select channels for scanning:
Press the or keys to select the desired channel.
1. If the icon is visible, the selected channel is already in the Scan Memory.
Press F followed by SQL to remove the channel from the scan memory. A low beep will
be heard and the icon will disappear.
2. If the icon is not visible the selected channel is not presently in the
scan memory. Press F followed by SQL to add the channel to the scan memory.
Scanning for Channels
1. To scan for channels, briey press F followed by the key. The icon will ash and the
channel numbers will change as the radio scans through the channels.
2. To change the scan direcon while scanning, briey press the or keys.
3. To stop scanning, briey press F followed by the key. The icon will stop ashing and
the radio will return to normal operaon.
There must be at least 2 channels stored in the scan memory. If not, the radio will not scan.
icon will disappear.
2. If the
TX677 Instrucon Manual
12 June 2018
© 2018 Standard Communicaons Pty Ltd trading as GME. All rights reserved.
21
50157
Content
Factory Reset
A factory reset clears any sengs you have made to your radio, and restores it to the default factory
sengs.
To perform a factory reset, press and hold the Menu and SQL keys simultaneously while switching the
radio on.
Scanning
Channel scanning allows you to monitor all channels for incoming signals.
While the radio is scanning, the Menu seng key is disabled.
Adding or Removing Channels
To select channels for scanning:
Press the or keys to select the desired channel.
1. If the icon is visible, the selected channel is already in the Scan Memory.
Press F followed by SQL to remove the channel from the scan memory. A low beep will
be heard and the
icon will disappear.
2. If the icon is not visible the selected channel is not presently in the
scan memory. Press F followed by SQL to add the channel to the scan memory.
Scanning for Channels
1. To scan for channels, briey press F followed by the key. The icon will ash and the
channel numbers will change as the radio scans through the channels.
2. To change the scan direcon while scanning, briey press the or keys.
3. To stop scanning, briey press F followed by the key. The icon will stop ashing and
the radio will return to normal operaon.
There must be at least 2 channels stored in the scan memory. If not, the radio will not scan.
icon is not visible the selected channel is not presently in
the scan memory. Press F followed by SQL to add the channel to
the scan memory.
SCANNING FOR CHANNELS
1. To scan for channels, briey press F followed by the  key. The
icon will ash and the channel numbers will change as the radio
scans through the channels.
2. To change the scan direction while scanning, briey press the 
or  keys.
3. To stop scanning, briey press F followed by the  key. The
TX677 Instrucon Manual
12 June 2018
© 2018 Standard Communicaons Pty Ltd trading as GME. All rights reserved.
21
50157
Content
Factory Reset
A factory reset clears any sengs you have made to your radio, and restores it to the default factory
sengs.
To perform a factory reset, press and hold the Menu and SQL keys simultaneously while switching the
radio on.
Scanning
Channel scanning allows you to monitor all channels for incoming signals.
While the radio is scanning, the Menu seng key is disabled.
Adding or Removing Channels
To select channels for scanning:
Press the or keys to select the desired channel.
1. If the icon is visible, the selected channel is already in the Scan Memory.
Press F followed by SQL to remove the channel from the scan memory. A low beep will
be heard and the icon will disappear.
2. If the icon is not visible the selected channel is not presently in the
scan memory. Press F followed by SQL to add the channel to the scan memory.
Scanning for Channels
1. To scan for channels, briey press F followed by the key. The icon will ash and the
channel numbers will change as the radio scans through the channels.
2. To change the scan direcon while scanning, briey press the or keys.
3. To stop scanning, briey press F followed by the key. The icon will stop ashing and
the radio will return to normal operaon.
There must be at least 2 channels stored in the scan memory. If not, the radio will not scan.
icon will stop ashing and the radio will return to normal operation.
Note: There must be at least 2 channels stored in the scan memory. If not, the
radio will not scan.