Why does my Goodman Amana AMEC80 Furnace fail to operate?
Your Goodman furnace might not be working due to several reasons: * A defective disconnect switch. * A defective door switch. * No 115 volt power. * No 24 volt power. To resolve this, determine the cause and restore the proper high and low volt power supply.
What to do if my Goodman Amana AMEC80 Furnace shows ten Red flashes on the control board?
If your Goodman furnace displays ten Red flashes on the control board, it indicates that gas valve current is detected with no call for heat. Ensure the gas valve isn't receiving voltage from an electrical short. If the valve wiring is correct, you may need to replace the control board.
What does it mean when my Goodman Amana AMEC80 shows five Red flashes on the control board?
Five Red flashes on the control board of your Goodman furnace indicates that the limit & rollout circuit has been open for 15 minutes, potentially due to an open control board fuse or rollout switch. Confirm electrically safe condition before proceeding with repairs.
What does it mean when my Goodman Amana AMEC80 Furnace shows four Red flashes on the control board?
If your Goodman furnace displays four Red flashes on the control board, it means there is an open limit circuit, which could be the main limit, aux limit, or roll out switch. Confirm electrically safe condition before proceeding with repairs.
What does it mean when my Goodman Amana AMEC80 Furnace shows seven Red flashes on the control board?
If your Goodman furnace shows seven Red flashes on the control board, it signifies a lockout due to excessive retries from flame not being proven during trial for ignition. Confirm electrical and gas safe conditions before proceeding with repairs.
What does it mean when my Goodman furnace shows six Red flashes on the control board?
If your Goodman furnace shows six Red flashes on the control board, it indicates a pressure switch cycling lockout, meaning the pressure switch has opened 5 times in the same heating cycle. Confirm electrically safe condition before proceeding with repairs.
What does it mean when my Goodman furnace shows one Red flash on the control board?
If your Goodman furnace displays one Red flash on the control board, it means that flame is sensed when no flame should be present. Confirm electrical and gas safe conditions before proceeding with repairs.
Why is my Goodman furnace showing rapid Amber flashes on the control board?
Rapid Amber flashes on your Goodman furnace's control board indicate a low flame sense current. Clean the flame rod with steel wool. Confirm electrically safe condition before proceeding with repairs.
What does it mean when my Goodman furnace shows three Amber flashes on the control board?
If your Goodman furnace displays three Amber flashes on the control board, it means there is a W2 call present without W1. Confirm electrically safe condition before proceeding with repairs.
What does it mean when my Goodman Amana AMEC80 Furnace shows four Amber flashes on the control board?
If your Goodman furnace displays four Amber flashes on the control board, it indicates that Ylo or Y call is present without G. Confirm electrically safe condition before proceeding with repairs.
Essential safety precautions and warnings for operating the furnace.
Step-by-step guide for safely operating the furnace.
Procedure for safely shutting off the gas supply to the furnace.
How to adjust the blower speed for optimal performance.
Configuration options using DIP switches on the control board.
Detailed explanation of the furnace's operational steps and cycles.
Operational steps and conditions for the heating mode.
Procedure for testing the multi-speed ECM circulator blower motor.
Procedure for measuring and adjusting temperature rise.
Troubleshooting and testing the redundant gas valve.
Procedure for measuring and adjusting gas manifold pressure.
Diagnosing issues with the integrated ignition control board.
Procedure for testing the flame sensor for combustion proof.
Reference chart for LED flash codes and their associated faults.
Procedure for retrieving and clearing fault codes from the control board.
General| Model | AMEC80 |
|---|---|
| Type | Gas Furnace |
| Efficiency Rating | 80% AFUE |
| Heating Capacity | 40, 000-120, 000 BTU/h |
| Blower Motor | Multi-Speed |
| Warranty | 10-Year Parts Limited Warranty; Lifetime Heat Exchanger Limited Warranty |
| Fuel Type | Natural Gas or Propane |
| Blower Motor Type | PSC |
| Heat Exchanger | Aluminized Steel Tubular |
| Stages | Single-stage |
To Next Page