PRODUCT IDENTIFICATION
13
MODEL # MFG # DESCRIPTION
DEHUM1
P1227801F
Dehumidistat. For use with Goodman® and Amana® Brand two-stage variable speed furnace
models ADV8, AMV8, ACV9, AMV9, GMV8, GCV9, GMV9, GMV95. Wall mounted, 24 volt
humidity control available as a Dehumidistat used to reduce the airflow in the air conditioning
mode when necessary to lower the humidity in an occupied home to prevent dew build-up
associated with high humidity levels. This control features a moisture-sensitive nylon element
and also provides positive ON-OFF settings for manual operation. The control is a normally
closed switch that opens on humidity rise causing the blower to switch to a lower speed to
control the humidity within the structure.
EFR01
P1221001
P1221002F
External Filter Rack Kit. For use with Goodman® and Amana® Brand 90% upflow variable
speed gas furnace models AMH95, AMS9, AMS95, GMH95, GMS9, GMS95, DMS9, AMV9,
GMV9, GMV95. This kit is intended to provide a location, external to the furnace casing, for
installation of a permanent filter. The rack is mounted over the indoor air blower compartment
area of either side panel, and provide filter retention as well as a location for attaching return air
ductwork.
FTK03A
P1171304F
P1171305F
Furnace Twinning Kit. This kit allows Goodman® or Amana® Brand single stage 80% and
single stage 90% gas furnaces to operate at the same time from a single thermostat. The two
furnaces to be "twinned" must be the exact same model with their circulating air blowers set to
deliver the same air flow at the same time. The furnaces may deliver different CFM's in the
cooling mode, if applicable. This kit cannot be used to control more than two furnaces.
HA02
P1129112F
High Altitude Kit. The kit is designed to convert Goodman®, Amana® Brand & Amana®
Distinctions™ Brand 80% gas furnace models (AMH8*, AMS8*, ADS8*, DMS8*, DDS8*, DHS8*,
GDS8*, GMH8*, GMS8*, GDS8*, GHS8*) for higher altitudes. This kit is required when installing
these furnaces above their maximum rated altitude. This kit contains
# 43-49, 55-58 gas orifices. The orifices in the kit have been selected as a result of testing with
the American Gas Association. They will provide appropriate derating at the altitude listed in the
High Altitude Charts as shown in the installation instructions of the kit.
HALP10
P1129112F
High Altitude Propane Gas Conversion Kit. Used on Goodman® and Amana® Brand 90%
single stage (ACS9, AMS9, DCS9, DMS9, GCS9, GMS9) furnace models. This kit is required
when installing furnaces above their maximum rated altitude. This kit contains propane gas
orifices. The orifices in the kit have been selected as a result of testing with the American Gas
Association. They will provide appropriate derating at the altitude listed in the High Altitude
Charts as shown in the installation instructions of the kit.
HALP11
P1129113F
High Altitude Propane Gas Conversion Kit. Used on Goodman® and Amana® Brand 90%
single stage (ACV9, AMV9, GCV9, GMV9, GMV95) furnace models. This kit is required when
installing furnaces above their maximum rated altitude. This kit contains propane gas orifices.
The orifices in the kit have been selected as a result of testing with the American Gas
Association. They will provide appropriate derating at the altitude listed in the High Altitude
Charts as shown in the installation instructions of the kit.
HALP13
P1129112F
High Altitude Propane Gas Conversion Kit. Used on Goodman® and Amana® Brand 90% two
stage (ACV9, GCV9) furnace models. This kit is required when installing furnaces above their
maximum rated altitude. This kit contains propane gas orifices. The orifices in the kit have been
selected as a result of testing with the American Gas Association. They will provide appropriate
derating at the altitude listed in the High Altitude Charts as shown in the installation instructions
of the kit.
To Next Page
Loading...
