Goodman MBE2000 - Wiring Diagrams: Heat Pump with Multiple Thermostats; Heat Pump - 2 Stage Aux Heat with 1 Outdoor Tstat; Heat Pump - 2 Stage Aux Heat with 2 Outdoor Tstats

WIRING DIAGRAMS
14
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
ROOM
THERMOSTAT
OT2
THERMOSTATS
W1
HEATER
OT1OW/W2E\W1 OTC
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 AND OT1 CLOSED ENABLES LO SPD FAN HEATING
W2 AND OT2 CLOSED ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 AND 0T2 PJ2 MUST BE CUT
FOR THIS CONFIGURATION
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
(CFM)
R
OT1
HUM
OT2
W2W1
HEATPUMP
COM
CONDENSER
YCON O EDW2
OUTDOOR
O
HEATPUMP
HEATPUMP
R
CONDENSER
YCON OCOM
RY
C
OT2
W2 ED
W2
OE
W2
HUMGY/Y2Y1RC
REMOVE
PRODUCTION
WIRE Y1 - O
DIP
1st STAGE HEATER
2nd STAGE HEATER
ON
OFF
SWITCH
W2
24 VAC
CR
Y1
HUMIDISTAT
IF NEEDED
G
C
R
Y
HUMIDISTAT
(OPTIONAL)
SEE NOTE 4
OT1
OT2
OUTDOOR
OT1OTC
NO AUX HEAT IN HEATPUMP MODE UNTIL OUTDOOR T'STAT CLOSES
HEATPUMP - 2 STG EMHT 2 STG AUX - 2 OUTDOOR T'STATS
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "
ON" POSITION
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 ENABLES LO SPD FAN HEATING
W2 AND OT2 CLOSED ENABLES HI SPD FAN HEATING
3.) 0T2 PJ2 MUST BE CUT FOR THIS CONFIGURATION
YCON
CONDENSER
R
R
HEATPUMP
COM O EDW2
HEATPUMP
C
Y
O
W2
OT2
PLEASE REFER
CONFIGURATION.
DIP SWITCH
FOR PROPER
TO MANUAL
(CFM)
HUM
DIP
OFF
ON
2nd STAGE HEATER
1st STAGE HEATER
Y
Y1
W1
HEATPUMP
OTC
CONDENSER
YCONR
OT1
COM O
E\W1 W/W2 O
SWITCH
HEATER
W2W1
W2
W2 ED
RC
24 VAC
THERMOSTATS
OUTDOOR
OT1 OT2 CRY1
IF NEEDED
THERMOSTAT
ROOM
W2
EO
R
C
G
SEE NOTE 4
REMOVE
PRODUCTION
WIRE Y1 - O
HUMIDISTAT
Y/Y2GHUM
HUMIDISTAT
(OPTIONAL)
1st STAGE AUX HEAT ENABLED BY ROOM T'STAT
2ND STAGE AUX ENABLED BY ROOM T'STAT AND OUTDOOR T'STAT
HEATPUMP - 2 STG EMHT 2 STG AUX - 1 OUTDOOR T'STAT
OUTDOOR
THERMOSTAT
4.)
CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "
ON" POSITION