Goodman MBE2000 - Wiring Diagrams: Heat Pump with 2 Stage Auxiliary Heat

WIRING DIAGRAMS
13
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
4.)
CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "
ON" POSITION
1st STAGE HEATER
REMOVE
PRODUCTION
WIRE Y1 - O
Y
ROOM
IF NEEDED
THERMOSTATS
THERMOSTAT
W2
EOC
RG
SEE NOTE 4
HUMIDISTAT
(OPTIONAL)
HUMIDISTAT
2nd STAGE HEATER
HEATPUMP - 2 STG EMHT 1 STG AUX HEAT
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 MUST BE CUT FOR THIS CONFIGURATION
CONDENSER
YCONR
R
HEATPUMP
COM O EDW2
C
HEATPUMP
Y
O
W2
Y/Y2GHUMOTCORCE\W1 W/W2 Y1OT1 OT2
Y1
DIP
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
(CFM)
ON
OFF
HEATPUMP
W1
PLEASE REFER
HUM
OT2
OT1
YCON
CONDENSER
R COM O
W2
HEATER
SWITCH
W2
W1
24 VAC
C R
W2 ED
OUTDOOR
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 ENABLES LO SPD FAN HEATING
W2 AND OT2 CLOSED ENABLES HI SPD FAN HEATING
3.) 0T2 PJ2 MUST BE CUT FOR THIS CONFIGURATION
YCON
CONDENSER
R
R
HEATPUMP
COM O EDW2
HEATPUMP
C
Y
O
W2
OT2
PLEASE REFER
CONFIGURATION.
DIP SWITCH
FOR PROPER
TO MANUAL
(CFM)
HUM
DIP
OFF
ON
2nd STAGE HEATER
1st STAGE HEATER
Y
Y1
W1
HEATPUMP
OTC
CONDENSER
YCONR
OT1
COM O
E\W1 W/W2 O
SWITCH
HEATER
W2W1
W2
W2 ED
RC
24 VAC
THERMOSTATS
OUTDOOR
OT1 OT2 CRY1
IF NEEDED
THERMOSTAT
ROOM
W2
EO
R
C
G
SEE NOTE 4
REMOVE
PRODUCTION
WIRE Y1 - O
HUMIDISTAT
Y/Y2GHUM
HUMIDISTAT
(OPTIONAL)
1st STAGE AUX HEAT ENABLED BY ROOM T'STAT
2ND STAGE AUX ENABLED BY ROOM T'STAT AND OUTDOOR T'STAT
HEATPUMP - 2 STG EMHT 2 STG AUX - 1 OUTDOOR T'STAT
OUTDOOR
THERMOSTAT
4.)
CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "
ON" POSITION