Goodman MBE2000 - Wiring Diagrams: Heat Pump Emergency Heat Scenarios

WIRING DIAGRAMS
17
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
Heat Pump with Single or Two-Stage Heating (Options for Emergency Heat)
with Conventional Thermostat
HEATPUMP - WITH 1 STG EMHT 1 STG AUX HEAT
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E AND W2 ENABLE HI SPD FAN HEATING
3.) IF OT2 PJ2 JUMPER IS CUT E AND W2 ENABLE
LO SPD FAN HEATING
HUMIDISTAT
(OPTIONAL)
IF NEEDED
OT2OT1 Y1W/W2E\W1 C ROOTC
CONFIGURATION.
DIP SWITCH
FOR PROPER
TO MANUAL
PLEASE REFER
CONDENSER
YCONR
DIP
(CFM)
ON
OFF
OUTDOOR
W1
HUM
OT2
OT1
W2
HEATPUMP
COM O W2 ED
SWITCH
HEATER
W1 W2
24 VAC
C R
THERMOSTATS
HUMGY/Y2
Y1
HUMIDISTAT
SEE NOTE 4
1st STAGE HEATER
ROOM
THERMOSTAT
ECRG
Y
HEATPUMP
RYCO
W2
HEATPUMP
YCON
CONDENSER
R COM O W2 ED
W2
O
REMOVE
PRODUCTION
WIRE Y1 - O
4.)
CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE "
ON" POSITION
RYCON
COM
O
W2 ED
HEATPUMP
CONDENSER
CO
W2
HEATPUMP
ROOM
THERMOSTAT
W2
E
C
YR
R
YG
IF NEEDED
HUMIDISTAT
(OPTIONAL)
REMOVE
PRODUCTION
WIRE Y1-O
SEE NOTE 4
2nd STAGE HEATER
1st STAGE HEATER
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E ENABLES LO SPD FAN HEATING
W2 ENABLES HI SPD FAN HEATING
3.) OT1 PJ4 MUST BE CUT FOR THIS CONFIGURATION
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE
IN THE "
ON" POSITION
J1
R1
R3
CR10
R2
CR9
PJ6
PJ2
PJ4
OT1
OT2
HUM
12345678
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
W1 W2
R
YCON COM
O
W2 ED
S
WI
TC
H
DI
P
O
N
O
FF
24 VAC
CR
Y1
W2W1
OUTDOOR
HEATPUMP
CONDENSER
DS1
CR1
CR2
CR5
CR6
CR7
CR8
CR3
CR11
J2 J3
1
4
C2
1
5
Y1RC G Y/Y2OT2 HUM
HUMIDISTAT
OT1
OTCW/W2E\W1
THERMOSTATS
GOODMAN MFG. CO. L.P.
HEATPUMP - 2 STG EMHT 1 STG AUX HEAT
O