Goodman UPFLOW - User Manual

19001 Kermier Rd, Waller, TX 77484
© 2021 Goodman Manufacturing Company, L.P.
www.goodmanmfg.com
1. Important Safety Instructions
The following symbols and labels are used throughout this
manual to indicate immediate or potential safety hazards. It
is the owner’s and installer’s responsibility to read and comply
with all safety information and instructions accompanying
these symbols. Failure to heed safety information increases
the risk of personal injury, property damage, and/or product
damage.
WARNING
HIGH VOLTAGE
DISCONNECT ALL POWER BEFORE SERVICING OR
INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY
BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY
DAMAGE, PERSONAL INJURY OR DEATH.
ONLY PERSONNEL THAT HAVE BEEN TRAINED TO INSTALL,
ADJUST, SERVICE OR REPAIR(HEREINAFTER, “SERVICE”)
THE EQUIPMENT SPECIFIED IN THIS MANUAL SHOULD
SERVICE THE EQUIPMENT. THE MANUFACTURER WILL
NOT BE RESPONSIBLE FOR ANY INJURY OR PROPERTY
DAMAGE ARISING FROM IMPROPER SERVICE OR SERVICE
PROCEDURES. IF YOU SERVICE THIS UNIT, YOU ASSUME
RESPONSIBILITY FOR ANY INJURY OR PROPERTY
DAMAGE WHICH MAY RESULT. IN ADDITION, IN
JURISDICTIONS THAT REQUIRE ONE OR MORE LICENSES
TO SERVICE THE EQUIPMENT SPECIFIED IN THIS
MANUAL, ONLY LICENSED PERSONNEL SHOULD SERVISE
THE EQUIPMENT.
IMPROPER INSTALLATION, ADJUSTMENT, SERVICING OR
REPAIR OF THE EQUIPMENT SPECIFIED IN THIS MANUAL,
OR ATTEMPTING TO INSTALL, ADJUST, SERVICE OR REPAIR
THE EQUIPMENT SPECIFIED IN THIS MANUAL WITHOUT
PROPER TRAINING MAY RESULT IN PRODUCT DAMAGE,
PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
WARNING
2. Shipping Inspection
Upon receiving the product, inspect it for damage from
shipment. Shipping damage, and subsequent investigation
is the responsibility of the carrier. Verify the model number,
specications, and accessories are correct prior to installation.
The distributor or manufacturer will not accept claims from
dealers for transportation damage or installation of incorrectly
shipped units.
UPFLOW/DOWNFLOW COILS
INSTALLATION INSTRUCTIONS
2.1 Handling
Use caution when transporting / carrying unit.. Do not carry
unit with hooks or sharp object. The preferred method of
carrying the unit after arrival at the job site is to carry by
two-wheel hand truck from the back or sides or by hand
by carrying at the cabinet corners.
3. Codes & Regulations
This product is designed and manufactured to comply with
national codes. Installation in accordance with such codes
and/or prevailing local codes/regulations is the responsibility
of the installer. The manufacturer assumes no responsibility
for equipment installed in violation of any codes or regulations.
The United States Environmental Protection Agency (EPA)
has issued various regulations regarding the introduction and
disposal of refrigerants. Failure to follow these regulations
may harm the environment and can lead to the imposition
of substantial nes. Should you have any questions please
contact the local o󰀩ce of the EPA.
4. Replacement Parts
Inspect the unit to verify all required components are present
and intact. Report any missing components immediately to
the manufacturer or to the distributor. Make sure to include
the full product model number and serial number when re-
porting and/or obtaining service parts. Replacement parts for
this product are available through your contractor or local
distributor. For the location of your nearest distributor consult
the white business pages, the yellow page section of the local
telephone book or contact:
HOMEOWNER SUPPORT
GOODMAN MANUFACTURING COMPANY, L.P.
19001 KERMIER ROAD
WALLER, TEXAS 77484
877– 254 – 4729
5. Pre-Installation Instructions
5.1 Preparation
Keep this document with the unit. Carefully read all instruc-
tions for the installation prior to installing product. Make
sure each step or procedure is understood and any special
considerations are taken into account before starting instal-
lation. Assemble all tools, hardware and supplies needed
to complete the installation. Some items may need to be
purchased locally. Make sure everything needed to install
the product is on hand before starting.
IO-4002
06/2021

Summary

Important Safety Instructions

Shipping Inspection and Handling

Handling

Instructions for safely transporting and carrying the unit to prevent damage or injury.

Codes, Regulations, and Replacement Parts

Codes & Regulations

Ensures installation complies with national and local codes and EPA refrigerant regulations.

Replacement Parts

Information on how to identify and obtain necessary replacement parts for the unit.

Pre-Installation Instructions

Preparation

Read all instructions, assemble tools, and ensure all supplies are ready before starting installation.

Clearances and Application Information

Clearances

Maintain minimum clearances for service and protect unit from physical damage.

Application Information

Coils are for indoor installation only, downstream of the furnace.

Condensate Drain Piping

Plastic Drain Pan Application

Condensate Drain Pan Break-away Feature

Describes the break-away feature on the drain pan for uncased installations.

Refrigerant Lines and TXV Adjustment

Refrigerant Lines

Covers connecting refrigerant lines, tubing size, preparation, and brazing procedures.

Tubing Connections for TXV Version

Details on connecting liquid and suction lines for TXV models.

Thermal Expansion Valve System Adjustment

Procedure for checking and adjusting TXV subcooling and superheat for proper operation.

Supply Duct Connection

Unit Components and Sealing

Filler Plates

Instructions on using filler plates for adapting units to different furnace sizes.

Return Ductwork

Warning against terminating return ductwork in areas with toxic or objectionable fumes.

Sealing Along The Panel Gap

Importance of applying insulation tape to prevent sweating and airflow leaks.

Removing Coil from Cabinet

Steps to remove and reinstall the coil from the cabinet for servicing.

Coil Cleaning and Start-Up Procedure

Aluminum Indoor Coil Cleaning

Recommended methods for cleaning aluminum evaporator coils safely and effectively.

Start-Up Procedure

Checks to perform before starting the unit, including electrical, tubing, and drainage.

Goodman UPFLOW Specifications

General

Brand	Goodman
Model	UPFLOW
Category	Furnace
Language	English