How to fix Goodwe Inverter Wi-Fi module if it fails to connect to the network?
If the Wi-Fi module fails to connect to the network after entering the correct router hotspot and password, the password might contain special characters not supported by the module. Change the password to include only Arabic numerals or uppercase/lowercase letters.
What to do if my Goodwe GW50KN-MT Inverter has Relay-Check Failure?
If your Goodwe Inverter shows a Relay-Check Failure: 1. Turn off the DC switch of the inverter. 2. Wait until the inverter's LCD light is off. 3. Turn on the DC switch and ensure it is connected.
What to do if my Goodwe GW50KN-MT shows 'Utility Loss'?
If your Goodwe Inverter displays a 'Utility Loss' error, it means it's not connected to the power grid. First, check if the power grid cable is properly connected. Also, verify the availability of the power grid itself.
Why is my Goodwe GW50KN-MT Inverter showing a 'Vac Failure'?
A 'Vac Failure' on your Goodwe Inverter indicates a grid voltage issue. The inverter should automatically restart within 5 minutes if the grid returns to normal. Ensure the grid voltage conforms to the specified requirements and that the neutral (N) and protective earth (PE) wires are securely connected.
How to fix a 'Fac Failure' on a Goodwe GW50KN-MT Inverter?
If your Goodwe Inverter is showing 'Fac Failure', this means the grid is not connected. Check the grid connection cables and verify the availability of the grid.
What to do if my Goodwe Inverter is overheating?
If your Goodwe Inverter is experiencing an 'Over Temperature' error, it means the internal temperature is higher than the specified normal value. Try to reduce the ambient temperature or move the inverter to a cooler location.
What does 'Ground I Failure' mean on my Goodwe GW50KN-MT?
If your Goodwe Inverter displays 'Ground I Failure', it indicates that the ground current is too high. Disconnect the inputs from the PV generator and inspect the peripheral AC system. Once the problem is resolved, reconnect the PV panel and check the Inverter status.
Why is my Goodwe GW50KN-MT showing 'PV Over Voltage'?
If your Goodwe Inverter is showing 'PV Over Voltage', verify that the PV open circuit voltage is not higher or too close to the maximum input voltage.
How to troubleshoot a 'Relay-Check Failure' on a Goodwe GW50KN-MT Inverter?
If your Goodwe Inverter displays 'Relay-Check Failure', turn off the DC switch of the inverter and wait until the LCD light turns off. Then, turn the DC switch back on, ensuring it is properly connected.
What does 'Isolation Failure' mean on my Goodwe GW50KN-MT?
If your Goodwe Inverter displays 'Isolation Failure', check the impedance between Ground and PV (+) & PV (-). The impedance value must be greater than 100k?. Also, ensure the inverter is properly earthed.
Details how to connect the inverter to the AC grid, including breaker specifications and wiring methods.
Recommends circuit breaker ratings and explains the need for residual current protection.
Describes the inverter's LCD panel and LED indicators for system status and operation.
Covers essential settings like language, time, communication, and safety configurations.
Presents detailed technical specifications for various MT series inverter models.
General| Model | GW50KN-MT |
|---|---|
| Rated Output Power | 50000W |
| Start Voltage | 250 V |
| Number of MPPT | 4 |
| MPPT Voltage Range | 200-850V |
| MPPT Efficiency | 99.9% |
| Efficiency | 98.6% |
| Max. Efficiency | 98.8% |
| Euro Efficiency | 98.3% |
| Max. AC Apparent Power | 55000VA |
| Rated Output Voltage | 400 V |
| AC Voltage Range | 310-480V |
| Frequency | 50/60Hz |
| THDi | <3% |
| DC Connection | MC4 |
| Protection Degree | IP65 |
| Cooling Method | Smart Fan Cooling |
| Weight | 70 kg |
| Protection Level | IP65 |
| Max Input Voltage | 1100V |
| Output Voltage | 400 V |
| Power Factor | 0.8 leading to 0.8 lagging |
| AC Connection | OT terminal |
| Operating Temperature Range | -25°C to 60°C |
| Humidity | 0-100% |
| Input Voltage Range | 200-1000V |
To Next Page