Why does my Graco Paint Sprayer run intermittently or very slowly?
If your Graco Paint Sprayer runs intermittently or very slowly: * Allow the sprayer to dry out if fluid has gotten into it. * The motor and/or Smartcontrol with enclosure may need replacement.
Why does my Graco 17N162 Paint Sprayer spray pattern spit at the end or beginning?
If your Graco Paint Sprayer's spray pattern spits at the end or beginning, it could be due to: * Excess material on the spray tip and guard, or a partially plugged tip; clean the spray tip and guard, and clear any clogs. * The spray tip not being fully inserted into the spray tip guard. * A worn or damaged spray tip; replace it. * The pump has reached its maximum life; replace the pump.
What to do if my Graco Paint Sprayer makes noise but won't spray?
If your Graco Paint Sprayer makes a sound but doesn't spray material, several issues could be the cause. First, ensure the Prime Pump/Spray knob is in the SPRAY position and the spray tip is also in the SPRAY position. Check if the speed control is set too low and increase it until the unit sprays. Refill the FlexLiner if the material level is low, and prime the pump. Other potential causes include a FlexLiner in the cup support, issues with the cup cover, the cup assembly not being properly locked, air in the FlexLiner, a clogged VacuValve, a dirty sprayer, improperly installed outlet valves, a clogged spray tip, debris in the paint, or a plugged pump filter. In some cases, it might indicate that the pump has reached the end of its life, or there is a locked rotor condition.
Why is my Graco 17N162 Paint Sprayer spraying poorly?
If your Graco Paint Sprayer is producing poor results, consider these possible causes and solutions: * A partially clogged spray tip: clear the clog. * Incorrect spray tip position: rotate the spray tip to the SPRAY position. * Using the wrong spray tip: install a different size spray tip. * A worn or damaged spray tip: replace the spray tip. * Aerated material: do NOT shake the material; stir it instead. * Material is too cold: warm the material. * Dirty or worn outlet valves: clean the outlet valves. * Pump at the end of its life: replace the pump assembly.
What to do if my Graco 17N162 spray pattern spits?
If your Graco Paint Sprayer's spray pattern "spits" at the beginning or end, the issue might be due to excess material on the spray tip guard assembly or a partially clogged spray tip; clean the spray tip guard. Ensure the spray tip is fully inserted into the spray tip guard. A worn spray tip could also be the cause, so consider replacing it. Also, the sprayer may be dirty, so flush it. In some cases, the front valve may have reached the end of its life and needs replacement.
How to eliminate tails in the spray pattern of my Graco 17N162?
If your Graco Paint Sprayer's spray pattern has tails, try the following: * Increase the speed control if it's set too low. * Install a different size spray tip. * Thin the material according to the paint manufacturer's recommendations. * Change to a different material if the current one is not compatible with the sprayer. * Replace the spray tip if it is worn or damaged.
What to do if my Graco 17N162 Paint Sprayer makes sound but doesn't spray?
If your Graco Paint Sprayer makes a sound when you pull the trigger, but no material is sprayed, consider the following: * Ensure the sprayer is primed. * Verify there's only one FlexLiner in the Cup Support. * Check the cup cover is correctly threaded and tightened to the Cup Support. * Confirm the cup assembly is properly locked onto the sprayer. * Make sure all air is out of the FlexLiner and the VacuValve is properly closed. * Clean the VacuValve reservoir and air hole. * Turn the Prime Pump/Spray knob to the SPRAY position and the Spray Tip to the SPRAY position. * Increase the speed control. Also, check for clogs in the spray tip, debris in the paint, or a plugged pump filter. Refill the FlexLiner if it's low on material. If none of these steps work, the pump may n...
Why will my Graco Paint Sprayer spray paint but not water?
If your Graco Paint Sprayer sprays paint but not water, consider the following: * Ensure there is only one FlexLiner in the Cup Support. * Check that the cup cover is properly threaded and tightened to the Cup Support. * Avoid flexing or pushing on the Cup Support when evacuating air from the FlexLiner. * Avoid pulling down on the FlexLiner when evacuating air. * Ensure there is no damage to the FlexLiner lip or the cup cover gasket. * Make sure the FlexLiner lip and cup cover gasket are free of debris and dried paint. * The pump assembly may need replacement.
Why is the spray pattern pulsating on my Graco 17N162 Paint Sprayer?
A pulsating spray pattern on your Graco Paint Sprayer can be caused by several factors: * Moving too fast while spraying; try slowing down your movement. * A clogged spray tip. * Material that is difficult to atomize; increase the speed on models with speed control. * Holding the sprayer too far from the surface; hold the sprayer farther away from the surface. * Using an incorrect spray tip for the material; install a different size spray tip.
What causes material leaks around the spray tip of Graco Paint Sprayer?
If material is leaking around the spray tip guard or spray tip handle of your Graco Paint Sprayer, the spray tip seal and seat may be damaged or not properly installed.
Covers electrical safety, proper grounding, and extension cord selection.
Details risks and precautions related to flammable materials and sparks.
Outlines procedures to prevent electric shock during operation and maintenance.
Warns about high-pressure fluid injection and necessary immediate actions.
Covers general misuse risks, PPE, and environmental considerations.
Addresses dangers of toxic fluids/fumes and necessary protective measures.
Specifies required PPE like eye protection, respirators, and gloves.
General| Type | Airless Paint Sprayer |
|---|---|
| Max Pressure | 3000 PSI |
| Maximum Operating Pressure | 3000 PSI |
| Flow Rate | 0.31 gpm |
| Horsepower | 5/8 hp |
| Power Source | Electric |
| Voltage | 120V |
| Weight | 20 lb |
| Maximum Tip Size | 0.017 inches |
| Hose Length | 25 feet |
| Spray Tip Size | 0.015 inches |
To Next Page
