Graco 17M363 - User Manual

Other manuals for Graco 17M363

Operation, Parts12 pages

Questions and Answers

E
Erin LeeAug 15, 2025
Why does my Graco 17M363 spray pattern “spit” at the end or beginning?
- A
  Amy DicksonAug 15, 2025
  If your Graco Paint Sprayer's spray pattern "spits" at the end or beginning, this could be due to: * Excess material accumulated on the Spray Tip and Spray Tip Guard, or the Spray Tip is partially plugged; clean the Spray Tip and Spray Tip Guard, and clear the Spray Tip. * The Spray Tip is not fully inserted into the Spray Tip Guard. * The Spray Tip is worn or damaged; replace it. * The pump has reached its maximum life; replace the pump.
D
Danielle CruzAug 18, 2025
Why does my Graco Paint Sprayer spray pattern have tails?
- T
  Tammy ArmstrongAug 18, 2025
  If the spray pattern of your Graco Paint Sprayer has tails, it could be due to several reasons: * The Speed Control might be set too low; increase the speed until the desired pattern is achieved. * You might be using the incorrect Spray Tip for the material; install a different size Spray Tip. * The material may need to be thinned; follow the paint manufacturer's recommendations. * The material might not be compatible with the sprayer; try a different material. * The Spray Tip could be worn or damaged; replace it.
J
Jessica StuartAug 21, 2025
Why does Graco Paint Sprayer spray tip continue to drip or ooze material after trigger is released?
- L
  Lisa MarshallAug 22, 2025
  If the Spray Tip on your Graco Paint Sprayer continues to drip or ooze material after you release the trigger: * The Spray Tip is likely worn and needs to be replaced. * The Spray Tip might not be fully inserted into the Spray Tip Guard.
C
cookjamesAug 25, 2025
What causes paint leaks out of the cup threads of my Graco Paint Sprayer?
- D
  Deborah SavageAug 25, 2025
  If paint leaks out of the cup threads of your Graco Paint Sprayer, consider these points: * Ensure there is only one FlexLiner in the Cup Support. * Make sure the cup cover is properly threaded to the Cup Support. If threads are visible when tight, remove and reinstall it so no threads are visible. * Ensure the cup cover is tightened so the arrow is within range of the indicator. * Avoid flexing or pushing on the Cup Support when you evacuate air from the FlexLiner. * Avoid pulling down on the FlexLiner when you evacuate air. * Check for damage to the FlexLiner lip or cup cover gasket. * Ensure the FlexLiner lip and cup cover gasket are free of debris and dried paint. * Replace the FlexLiner.
J
Jerry WilliamsAug 28, 2025
What to do if my Graco 17M363 Paint Sprayer makes sound but no material is sprayed?
- V
  Vincent RasmussenAug 28, 2025
  If your Graco Paint Sprayer makes sound, but no material is sprayed when you pull the trigger, here are some things to check: * Ensure the Prime Pump/Spray knob is in the SPRAY position. * Confirm the Spray Tip is in the SPRAY position. * Increase the speed control. * Refill FlexLiner with material and prime the pump if the material level is low. * Replace pump assembly if the pump has reached the end of its life.
S
Sue LopezAug 31, 2025
What to do if my Graco 17M363 Paint Sprayer spray pattern is pulsating?
- H
  humphreytimothyAug 31, 2025
  If the spray pattern of your Graco Paint Sprayer is pulsating, consider the following: * Reduce the speed of movement. * If the Spray Tip is clogged, clean it. * If the material is difficult to atomize and if your model has a Speed Control, increase the speed until you achieve the desired pattern. * Adjust the distance; hold the sprayer farther away from the surface. * The Spray Tip might be incorrect for the material; install a different size Spray Tip.
K
Katie HernandezSep 4, 2025
What to do if my Graco Paint Sprayer sprays with poor results?
- V
  velasquezronaldSep 4, 2025
  If your Graco Paint Sprayer is spraying with poor results, here are some potential causes and solutions: * If the Spray Tip is partially clogged, clean it. * Ensure the Spray Tip is in the correct SPRAY position. * You might be using the incorrect Spray Tip for the application; install a different size Spray Tip. * If the Spray Tip is worn or damaged, replace it. * If the material is too cold to spray, warm it up. * If the pump has reached the end of its life, replace the pump assembly.
P
Philip AvilaSep 7, 2025
How to fix dripping or sagging spray pattern with Graco Paint Sprayer?
- A
  Amy BakerSep 7, 2025
  To fix a dripping or sagging spray pattern with your Graco Paint Sprayer: * Move the sprayer faster when spraying. * Move the sprayer away from the surface. * Release the trigger when changing directions. * If your model has Speed Control, decrease the speed until the desired pattern is achieved. * Replace the Spray Tip if it is worn or damaged.
P
Paula VaughnSep 12, 2025
What to do if my Graco 17M363 Paint Sprayer makes no sound when trigger is pulled?
- F
  Felicia LeeSep 12, 2025
  If your Graco Paint Sprayer makes no sound when you pull the trigger, here are some possible causes and solutions: * If the Diagnostic Light blinks two times, replace the battery with a charged one, as this indicates incorrect voltage. * If the battery has reached the end of its life, replace it. * If the Diagnostic Light blinks three times, allow the battery to cool down or warm up to room temperature, as this indicates the battery temperature is too hot or cold. * If the Diagnostic Light blinks four times, replace the pump and/or motor assembly, as this indicates a locked rotor condition. * If the Diagnostic Light does not blink, install or replace the battery, as this indicates the battery is either not installed or damaged. * Replace the Smartcontrol.