Graco APEX 260106 - User Manual

Questions and Answers

B
Barbara AshleyAug 9, 2025
Why won't my Graco Water Pump prime, even though the motor is running?
- F
  fwaltersAug 9, 2025
  If the Graco Water Pump motor runs but the pump won't prime, several issues could be the cause. Begin by checking for dirt under the pressure relief valve or seal; if present, remove the valve and clean or replace any damaged parts. Also, inspect the gears for wear or damage, replacing them if necessary. Ensure the fluid level is adequate and the cover seal is intact; refill the tank if low and replace the seal if damaged. Clear any clogs from the inlet strainer and ensure all joints in the suction tube are sealed to prevent air leaks. If using a filter, meter, or automatic shut-off nozzle, an air lock may have formed; fill the pump and meter with fuel to resolve this. Finally, verify the motor is running at the correct speed by checking electrical connections and supply voltage.
B
Bonnie JohnsonAug 14, 2025
What to do if my Graco Water Pump has low output flow?
- S
  scott95Aug 14, 2025
  If the Graco Water Pump unit pumps but the output flow is low, there are several potential causes. First, check the inlet strainer for clogs and clean or replace it as needed. Ensure there are no air leaks in the suction tube by verifying all joints are properly sealed. The suction tube should also have a minimum clearance of 2 inches from the tank bottom. Confirm that the tank is adequately vented to the atmosphere and is not empty; refill if necessary. Inspect the gears for wear or damage, replacing them if found. Also, check the suction tube, hose, and nozzle for any obstructions and clean them. If none of these steps resolve the issue, the motor may be damaged and require replacement.
C
cadamsAug 19, 2025
Why is my Graco Water Pump motor overheating?
- D
  dwayne64Aug 19, 2025
  If the Graco Water Pump motor is overheating, several factors could be contributing. Check the gears to ensure they turn freely on the shaft; binding gears can cause overheating. Avoid operating the pump with the nozzle closed for more than 5 minutes. Inspect the strainer, suction tube, hose, and nozzle for clogs, cleaning or replacing as needed. Limit continuous operation to a maximum of 30 minutes per hour to prevent overheating.
J
John RaymondAug 25, 2025
What causes a Graco Water Pump motor to stall when the nozzle is closed?
- J
  Jennifer SharpAug 25, 2025
  If the Graco Water Pump motor stalls when the nozzle is closed, it might be due to several reasons. First, inspect the bypass relief valve to ensure the ball is free and replace it if damaged. Check the supply voltage to rule out low voltage as a cause. Inspect the gears for damage, ensuring they turn freely, and replace them if necessary. If these steps don't resolve the issue, the motor itself may be faulty and require replacement.
S
Sarah PetersonAug 28, 2025
How to fix a Graco APEX 260106 Water Pump when the switch won't turn it on?
- D
  davilacourtneyAug 29, 2025
  If the switch won't turn on your Graco Water Pump, start by checking the fuse or circuit breaker and replace or reset it as needed. Verify that the supply voltage is correct for the pump motor. If the issue persists, the switch itself may be defective (particularly on model 260240), so check and replace it if necessary. Finally, inspect the motor for damage or defects and replace it if needed.
G
Gabriela RobertsSep 3, 2025
Why is my Graco APEX 260106 Water Pump leaking oil in the motor mount?
- A
  amycarrollSep 3, 2025
  If oil is leaking in the motor mount of your Graco Water Pump, it could be due to a faulty or damaged motor shaft seal, which should be replaced. Avoid operating the pump for extended periods with the nozzle closed (do not exceed 5 minutes). Also, inspect the motor shaft for wear; if there's a groove worn in the seal area, replace the motor.