309226 21
Technical Data
MAGNUM DX MAGNUM XR5 MAGNUM XR7 MAGNUM XR9
Working pressure
range
0 to 2800 psi
(0 to 19 MPa, 0 to 193
bar)
0 to 3000 psi
(0 to 21 MPa, 0 to 207
bar)
0 to 3000 psi
(0 to 21 MPa, 0 to 207
bar)
0 to 3000 psi
(0 to 21 MPa, 0 to 207
bar)
Electric motor
(open-frame,
permanent magnet DC)
6.5 Amp
5.8 Amp
5.8 Amp 4.9 Amp
Operating horsepower 3/8
5/8
3/4 7/8
Maximum delivery (with
tip)
0.24 gpm (.91 lpm)
0.27 gpm (1.02 lpm)
0.31 gpm (1.17 lpm) 0.38 gpm (1.44 lpm)
Paint hose 25 ft (7.6 m) x 3/16 in.
25 ft (7.6 m) x 1/4 in.
50 ft (15.2 m) x 1/4 in. 50 ft (15.2 m) x 1/4 in.
Maximum tip hole size 0.015 in. (0.38 mm)
0.015 in. (0.38 mm)
0.017 in. (0.43 mm) 0.019 in. (0.48 mm)
Weight, sprayer only 13 lb (6 kg)
21 lb (10 kg)
31 lb (14 kg) 35 lb (16 kg)
Weight, sprayer, hose,
& gun
16 lb (7.25 kg)
24 lb (11 kg)
36 lb (17 kg) 40 lb (18 kg)
Dimensions 14.9 in. (37.8 cm) L
15.0 in. (38.1 cm) W
15.6 in. (39.6cm) H
13.75 in. (34.9 cm) L
11 in. (27.9 cm) W
17 in. (43.2 cm) H
19.5 in. (49.5 cm) L
17.25 in. (43.8 cm) W
40.75 in. (103.5 cm) H
Height with folded
handle is
26 in. (66 cm)
19.5 in. (49.5 cm) L
19 in. (48.3 cm) W
40 in. (101.6 cm) H
Height with folded
handle is
26 in. (66 cm)
Power cord 16 AWG, 3 wire, 6 ft
(1.8 m)
16 AWG, 3 wire, 6 ft
(1.8 m
16 AWG, 3 wire, 6 ft
(1.8 m)
16 AWG, 3 wire, 10 ft
(3 m)
Pump inlet fitting 3/4 in. internal thread (standard garden hose thread)
Fluid outlet fitting 1/4 npsm external thread
Inlet screen on suction
tube
14 mesh (1300 micron)
Wetted parts, pump &
hose
stainless steel, brass, leather, ultra-high molecular weight polyethylene (UHMWPE), carbide, nylon,
PVC, zinc-aluminum alloy, polypropylene
Wetted parts, gun SG1–EF: plated steel, nylon, aluminum, tungsten carbide, stainless steel, brass, viton
SG2 / SG3: aluminum, brass, carbide, nylon, plated steel, stainless steel, UHMWPE, zinc
Generator requirement 1500 Watt minimum
Electrical power
requirement
120V AC, 60 Hz, 1 phase, 15A
Storage temperature
range * {
–30_ to 160_ F (–35_ to 71_ C)
Operating temperature
range **
40_ to 115_ F (4_ to 46_ C)
* When pump is stored with non-freezing fluid. Pump damage will occur if water or latex paint freezes in pump.
{ Damage to plastic parts may result if impact occurs in low-temperature conditions.
* * Changes in paint viscosity at very low or very high temperatures can affect sprayer performance.
To Next Page
Loading...
