EasyManua.ls Logo

Graco TX 90 - User Manual

Graco TX 90
18 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operation
Interior Texture Sprayers
TX 90 and TX 125
For Water-Based Materials Only
Models:
254971 & 254986
60 psi (4.14 bar) Maximum Fluid Working Pressure
254972
70 psi (4.9 bar) Maximum Fluid Working Pressure
Related Manuals
Important Safety Instructions.
Read all warnings and instructions in this
manual. Save these instructions.
311777
311770
Model 254972 Shown
ti8696a
311764D
EN

Table of Contents

Other manuals for Graco TX 90

Preview: Repair Manual
Repair Manual32 pages
Preview: Troubleshooting Manual
Troubleshooting Manual24 pages

Questions and Answers

  • J
    Joseph Barnes PhDSep 8, 2025
    How to fix slow application speed on a Graco TX 90 Paint Sprayer?
    • C
      Carrie RussellSep 8, 2025
      If your Graco Paint Sprayer's application speed is slow, consider the following: * The material might be too thick. Thin the material. * The nozzle might be too small. Change to a larger nozzle. * Too much air might be used. Partially close the gun air valve to reduce airflow. * The pump hose might be worn. Replace the hose. * The gun might be plugged or dirty. Clean the gun. * The hose might be kinked. Unkink the hose. * The gun adjustment might be set too low. Increase the flow adjustment with the flow adjustment nut. * There might be too many items on the same circuit. Unplug other items from the circuit. * The extension cord might be too long or the wrong gauge. Use a different extension cord.
  • A
    Adam MartinSep 10, 2025
    How to fix a Graco TX 90 Paint Sprayer quick disconnect that won't stay connected?
    • S
      Shawn GarzaSep 10, 2025
      If the quick disconnect on your Graco Paint Sprayer doesn't stay connected, it might be due to a dirty or corroded fitting. Clean it thoroughly, soak it in oil, and apply a few drops of light oil.
  • M
    Marvin WagnerSep 12, 2025
    What to do if the needle adjustment on my Graco TX 90 won’t adjust?
    • G
      Gregory HarringtonSep 12, 2025
      If the needle adjustment on your Graco Paint Sprayer won’t adjust, it might be because: * The threads are dirty. Clean the threads. * The nozzle is not on the gun. Put the nozzle on the gun.
  • T
    Travis MosleySep 13, 2025
    Why is there no air coming from the compressor on my Graco TX 90 Paint Sprayer?
    • A
      Anne CookSep 14, 2025
      If there's no air coming from the compressor of your Graco Paint Sprayer, first, ensure the gun air valve is open. Check the extension cord length and gauge, replacing it if it doesn't meet the recommendations. Clean the needle and retry. Check all quick disconnect connections to the gun and hoses. Replace the hose if it's damaged.
  • A
    Amanda TorresSep 15, 2025
    Why won’t the needle adjustment adjust on my Graco Paint Sprayer?
    • S
      Sharon MorrisSep 15, 2025
      If the needle adjustment on your Graco Paint Sprayer won’t adjust, the threads may be dirty, so clean them. Ensure the nozzle is properly attached to the gun.
  • A
    Adam WillisSep 18, 2025
    What to do if the quick disconnect does not stay connected on my Graco TX 90 Paint Sprayer?
    • H
      hansonwendySep 18, 2025
      If the quick disconnect on your Graco Paint Sprayer does not stay connected, the fitting may be dirty or corroded. Clean it thoroughly, soak it in oil, and apply a few drops of light oil.

Graco TX 90 Specifications

General IconGeneral
BrandGraco
ModelTX 90
CategoryPaint Sprayer
LanguageEnglish

Related product manuals