Graco Tradeworks 150 User Manual

313381L
Operation
Tradeworks
™
Project Painter,
Tradeworks
™
150 and Tradeworks
™
170
(Specifications, page 10.)
Tradeworks 150
Model: 826620
Tradeworks 170
Model: 826630
IMPORTANT SAFETY INSTRUCTIONS.
Read all warnings and instructions in this
manual and related manuals. Be familiar
with the controls and the proper usage of
the equipment. Save these instructions. See
page 10 for model and series information
including dispense rate, recommended
hose length, guns, and maximum working
pressure.
Tradeworks Project Painter
Model: 826610
ti12937a
FIRE AND EXPLOSION HAZARD
• Use only non-flammable or water-based materi-
als, or non-flammable paint thinners. Do not use
materials having flash points lower than 100°F
(38°C). This includes, but is not limited to, ace-
tone, xylene, toluene, and naphtha. For more
information about your material, request Safety
Data Sheet (SDS) from the supplier.
• Spraying flammable or combustible materials in
a factory or fixed location must comply with
NFPA 33 and OSHA 1910.94(c) requirements in
the USA and with all similar local regulations in
other countries.
- For portable spray applications of architectural paints and coatings -
Visit our website:
http://tradeworkssprayers.com
EN

Graco Tradeworks 150 Specifications

General

Brand	Graco
Model	Tradeworks 150
Category	Paint Sprayer
Language	English

Summary

Operation

IMPORTANT SAFETY INSTRUCTIONS

Key safety precautions and warnings for operating the equipment.

FIRE AND EXPLOSION HAZARD

Warning regarding fire and explosion risks associated with spraying flammable materials.

Warnings

Grounding Instructions

Instructions on proper grounding of the sprayer for electrical safety.

Warnings

ELECTRIC SHOCK HAZARD

Warning about the risks of electric shock due to improper grounding or setup.

Warnings

SKIN INJECTION HAZARD

Warning about the dangers of high-pressure fluid injection and bodily injury.

Warnings

EQUIPMENT MISUSE HAZARD

Hazards related to improper use of the sprayer, potentially causing injury or death.

MOVING PARTS HAZARD

Risks associated with moving parts of the equipment and how to avoid injury.

QUICK START-UP GUIDE

SETUP

Steps for preparing the sprayer for initial use.

FLUSHING

Procedure for flushing the sprayer system with cleaning fluid.

QUICK START-UP GUIDE

PRIMING

Process for filling the sprayer system with paint.

SPRAYING

Instructions on how to operate the sprayer for painting.

QUICK START-UP GUIDE

SHUTDOWN AND CLEANING - WATER-BASED PAINTS*

Steps for shutting down and cleaning the sprayer after use with water-based paints.

Specifications

Installation

Grounding and Electric Requirements

Essential requirements for safe electrical connection and grounding of the sprayer.

Thermal Overload

Explanation of the sprayer's thermal overload protection feature.

Component Identification - Tradeworks Project Painter

Component Identification - Tradeworks 150 and 170

Operation

Trigger Lock

How to use the trigger lock to prevent accidental spraying.

Pressure Relief Procedure

Steps to safely relieve pressure in the sprayer system before servicing.

Pressure Control Knob Settings

Explanation of the different settings for the pressure control knob.

Setup

Setup

Prime and Flush Storage Fluid

Procedure for priming the sprayer and flushing out storage fluid.

Setup

Install Tip and Guard on Gun

Instructions for installing the spray tip and guard onto the spray gun.

Setup

Spraying Techniques

Techniques for achieving a good spray pattern and preventing tip wear.

Unclogging Spray Tip

Steps to clear a clogged spray tip without disassembling the gun.

Setup

Tip Selection

Guidance on selecting the appropriate spray tip hole size for different coatings.

Getting Started With Basic Techniques

Aiming Gun

Proper technique for aiming the spray gun to achieve an even finish.

Triggering Gun

How to properly trigger and release the spray gun for consistent spray.

Shutdown and Cleaning

Pail Flushing

Procedure for flushing the sprayer system using paint pails.

Shutdown and Cleaning

Power Flush

A faster method for flushing the sprayer, used with water-based coatings.

Shutdown and Cleaning

Cleaning Gun

Detailed steps for cleaning the spray gun components.

Storage

Short Term Storage

Instructions for storing the sprayer for periods up to two days.

Long Term Storage

Procedure for storing the sprayer for periods longer than two days, including fluid recommendations.

Storage

Stowing Sprayer

Final steps for preparing the sprayer for storage, including securing components.

Maintenance and Service

Caring for Sprayer

General advice on keeping the sprayer clean and in good working order.

Pump Packings (150/170)

Information on pump packing wear, leaking, and replacement for specific models.

Paint Hoses

Guidelines for inspecting and using paint hoses, including length and damage checks.

Troubleshooting

Technical Data

Graco Standard Warranty

Graco Information

Contact information and website for Graco products and support.