GRAUPNER mc-32

324 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

123

Detail program description - Dual Rate / Expo | Winged models

0%

0%

0%

Aileron

Elevator

Rudder

DUAL

–––

–––

SEL

–––

–––

–––

100%

111%

100%

EXPO

SEL

G3

Normal

The vertical dashed line shows the current elevator

joystick position.

Set the Expo values as necessary in the same

manner.

Table of Contents

General Notices Table of Contents2
- Table of Contents2
- Environmental Protection Notices3
- Safety Notices4
- Safety Notices and Handling Regulations for Lithium-Ion (Liio) and Lithium-Polymer (Lipo) Batteries7
- Foreword10
- Remote Control Set Description11
- Technical Data14
- General Operating Notices Transmitter16
  - Opening the Transmitter Housing16
  - Transmitter Power Supply16
  - Recommended Chargers17
  - Battery Operation Timer in Display18
  - Lithium Battery, CR 203218
  - Joystick Length Adjustment18
  - Joystick Conversions19
  - Holder Bracket for Transmitter Straps20
  - Installing Additional Controls, Switches, Etc20
  - Aligning the Antenna20
  - Transmitter Description Front Side21
- Commissioning the Transmitter42
  - Firmware Update Via PC43
- Commissioning the Receiver46
  - Receiver System Power Supply47
  - General Charging Notices49
  - Firmware Update50
- Installation Notices52
- Term Deﬁ Nitions54
- Assigning Transmitter Controls, Switches and Control Switches56
- Digital Trim58
- Winged Models60
  - Receiver Layout61
- Helicopter Models64
  - Receiver Layout65
- Loading a New Memory Location66
- Model Select69
- Copy / Erase70
  - Erase Model70
  - Copy Model  Model70
  - Export to SD Card71
  - Import from SD Card72
  - Copy Fl Ight Phase72
  - Changes73
- Suppress Codes74
- Suppress Models75
- Basic Settings, Model76
  - Binding Receivers77
  - Range Test80
  - Helicopter Model84
    - Binding Receivers85
    - Range Test88
- Model Type94
- Helicopter Type98
- Servo Adjustment102
- Stick Mode104
  - Helicopter Model106
- Control Adjust108
  - Helicopter Model112
- Dual Rate / Expo120
  - Helicopter Model124
- Channel 1 Curve128
  - Winged Model128
  - Helicopter Model131
- Switch Display134
- Control Switch135
- Logical Switches138
  - How Do I Program a Fl Ight Phase140
- Phase Settings142
  - Helicopter Model146
- Phase Assignment148
- Phase Trim« (Winged Model)150
- Non-Delayed Channels151
- Timers (General)152
- Timers156
  - What Is a Mixer159
- Wing Mixers160
  - Aileron163
  - Aileron and 1 Camber Fl Ap164
  - Ailerons166
  - 2/4 Ailerons and 1/2/4 Camber Fl Aps168
Helicopter Mixer176
- Adjusting the Throttle and Pitch Curve187
- Autorotation Setting190
- General Remarks about Freely Progr. Mixers192
Free Mixers193
- Linear Mixers197
- Exponential Mixers199
- Examples201
MIX Active/Phase204
MIX Only Channel205
Dual Mixer206
Swashplate Mixer208
Fail Safe208
Teacher/Pupil210
- Connection Schematic213
- Wireless Hott System214
Transmitter Output218
Proﬁ -Trim220
- Winged Model220
- Helicopter Model222
Trim Memory224
- Winged Model224
- Trim Memory Winged Model224
- Helicopter Model226
Telemetry228
- Setting & Dataview229
  - Satellite Mode of Two Receivers238
  - Sensor/S239
- Selecting Sensors240
- RF Status View241
- Select Voice Update242
Channel Sequence244
Multichannel246
Ring Limiter250
MP3-Player254
General Basic Settings256
Servo Display262
Servo Test263
Code Lock264
Info Display266
Programming Examples Introduction268
- Winged Model First Steps270
- Helicopter Model308
Appendix Fcc Declaration318
- Fcc Information318
- Conformity Declaration319
- Guarantee Certiﬁ Cate320

Other manuals for GRAUPNER mc-32

Manual345 pages

Related product manuals

GRAUPNER mc-32 HoTT

Preview: GRAUPNER Kingpad mc-32 Edition

GRAUPNER Kingpad mc-32 Edition

Preview: GRAUPNER MC-32EX

GRAUPNER MC-32EX

Preview: GRAUPNER mc-16

Preview: GRAUPNER MC-28

Preview: GRAUPNER mc-26

Preview: GRAUPNER MC-20 HoTT

GRAUPNER MC-20 HoTT

GRAUPNER HoTT MC-20 Series

Preview: GRAUPNER HoTT MC-16 Series

GRAUPNER HoTT MC-16 Series

Preview: GRAUPNER mx-16 ifs

GRAUPNER mx-16 ifs

Preview: GRAUPNER MX-12 - PROGRAMMATION

GRAUPNER MX-12 - PROGRAMMATION