11
●
●
●
NOTE
●
●
no display
Sleep button
Timer button
LR-swing button
Press this button can select left & right swing angle.
Fan blow angle can be selected circularly as below:
●
●
●
position)
(stops at current
NOTE
The air conditioner is mainly used for controlling the te-
mperature, while the humidity control is the auxiliary fu-
nction. The humidity will be affected by the factors such
as indoor and outdoor
environment, degree of indoor
sealing and indoor flow.
When the set humidity is higher than current atmospheric
humidity, the set humidity can't be reached.
the humidity sensor is with malfunction, humidity
se
If
tting under cooling mode or dehumidification mode
will stop and the unit operates under general cooling
mode or dehumidification mode.
●
NOTE
●
●
Time setting range: 0.5-24 hours.
Time interval between two operations can’t exceed 5s.
Otherwise, remote controller will exit the setting status
automatically.
●
●
At ON status, press this button once can set
TIMER OFF. The character of HOUR and OFF
will flash. Press "+" or "-" button within 5s can
Sleep 1 is Sleep mode 1, in Cool modes: sleep sta-
and humidity value "88"; you can press "+" and "-"
buttons to set the humidity value.
Humidity setting range for the remote control-
ler:30%-70%.
Temperature can't be adjusted under humidity
control with dehumidification mode.
When continuous dehumidification is set, the
remote controller will display " " ; the remote
controller and indoor unit will display "Co".
Temperature can't be adjusted under continuous
dehumidification mode.
Under continous dehumidification mode, the unit
always works under dehumidification status; no
need to set temperature and humidity.
adjust the time of TIMER OFF. After each
pressing of "+" or "-" button, time will increase or
decrease half an hour. When holding "+" or "-"
button, 2s later, the time will change quickly until
to reach to your required time. After that, press
"Timer" button to confirm it. The character of
HOUR and OFF won't flash again.
Cancel TIMER OFF: Press "Timer" button again
under TIMER OFF status.
At OFF status, press this button once can set
TIMER ON. Please refer to TIMER off for
detailed operation.
Cancel TIMER ON: Press "Timer" button again
under TIMER ON status.
Press this button, can select Sleep 1 ( ), Sleep 2
( ), Sleep 3 ( ) and cancel the Sleep, circulate
between these, after electrified, Sleep Cancel is de-
faulted.
Press this button continuously more than 2s, the main
unit will swing back and forth from left to right, and
then loosen the button, the unit will stop swinging and
present position of guide louver will be kept immedi-
ately.
Under swing left and right mode, when the status is
switched from off to , if press this button again
2s later, status will switch to off status directly; if
press this button again within 2s, the change of swing
status will also depend on the circulation sequence
stated above.
This function only applicable for some models.
tus after run for one hour, the main unit setting tem-
perature will increase 1 , two hours, setting temper-
ature increased 2 , then the unit will run at this set-
ting temperature; In Heat mode: sleep status after
run for one hour, the setting temperature will de-
crease 1 , two hours, setting temperature will de-
crease 2 , then the unit will run at this setting tem-
perature.
Sleep 2 is sleep mode 2, that is air conditioner will
run according to the presetting a group of sleep tem-
perature curve.
Sleep 3 the sleep curve setting under Sleep mode
by DIY;
(1)
Under Sleep 3 mode, press "I Feel" button for a
long time, remote controller enters into user indivi-
emit eht ,emit siht ta ,sutats gnittes peels noitaud
of remote controller will display "1HOUR", the set-
ting temperature "88" will display the correspond-
ing temperature of last setting sleep curve and blink
(The first entering will display according to the initial
curve setting value of original factory);
(2) Adjust " + " and " - " button, could change the
corresponding setting temperature, after adjusted,
press "
I Feel
" button for confirmation;
(3) At this time, 1hour will be automatically increas-
ed at the timer position on the remote control, (that
is "2HOUR" or "3HOUR" or "8HOUR"), the place of
setting temperature "88" will display the corres-
To Next Page
Loading...
