48
Technical Information
Service Manual
succeeded. After powered on, 12:00 is defaulted to display and
signal will be displayed. If there is signal be displayed that
denotes the current time value is clock value, otherwise is timer
value.
9.
TIMER ON
TIMER OFF
button
● Timer On setting: Signal "ON" will blink and display, signal
will conceal, the numerical section will become the timer on
setting status. During 5 seconds blink, by pressing + or - button
to adjust the time value of numerical section, every press of that
button, the value will be increased or decreased 1 minute. Hold
pressing + or - button, 2 seconds later, it quickly change, the way
of change is: During the initial 2.5 seconds, ten numbers change
in the one place of minute, then the one place is constant, ten
numbers change in the tens place of minute at 2.5 seconds
speed and carry. During 5s blink, press the timer on button, the
timer setting succeeds. The timer on has been set up, repress
the timer on button, the timer on will be canceled.Before setting
the timer, please adjust the clock to the current actual time.
● Timer Off setting: Signal "OFF" will blink and display, signal
will conceal, the numerical section will become the timer off
setting status. The method of setting is the same as for TIMER
ON.
10.
TEMP
button
By pressing this button, you can see indoor set temperature,
indoor ambient temperature or outdoor ambient temperature on
indoor unit's display. The setting on remote controller selected
circularly as below:
no display
When selecting " " with remote controller or no display,
temperature indicator on indoor unit displays set temperature.
When selecting " " with remote controller, temperature indicator
on indoor unit displays indoor ambient temperature; When
selecting " " with remote controller, temperature indicator
on indoor unit displays outdoor ambient temperature. 3s later it
will return to the setting temprature or it depends on the other
received signal within 3s.
Attention: When displaying the outdoor ambient, the displaying
range is 0-60°C. When it goes beyond the range, it keeps the
threshold data (The smallest — 0°C and the largest 60°C).
Warm tips: When operating buttons on the cover please make
sure the cover is closed completely.
NOTICE:
● Outdoor temperature display is not available for some models.
At that time, indoor unit receives " " signal, while it displays
indoor set temperature.
11. button
Press this button to achieve the on and off of health and
scavenging functions in operation status. Press this button for
the first time to start scavenging function simultaneously; LCD
displays " ". Press the button for the second time to start health
and scavenging functions simultaneously; LCD displays " "
and " ". Press this button for the third time to quit health and
scavenging functions simultaneously. Press the button for the
fourth time to start health function; LCD display " ".
Press this button again to repeat the operation above.
NOTICE:
● This function is applicable to partial of models.
12.
I FEEL
button
Press this button to start I FEEL function and " " will be
displayed on the remote controller. After this function is set, the
remote controller will send the detected ambient temperature
to the controller and the unit will automatically adjust the indoor
temperature according to the detected temperature. Press this
button again to close I FEEL function and " " will disappear.
Please put the remote controller near user when this function
is set. Do not put the remote controller near the object of high
temperature or low temperature in order to avoid detecting
inaccurate ambient temperature. When I FEEL function is turned
on, the remote controller should be put within the area where
indoor unit can receive the signal sent by the remote controller.
13.
LIGHT
button
Press this button to turn off display light on indoor unit. " " icon
on remote controller disappears. Press this button again to turn
on display light. " " icon is displayed.
14.
WiFi
button
Press "WiFi" button simultaneously to turn on or turn off WIFI
function. When WIFI function is turned on, the "WiFi" icon will
be displayed on remote controller; Under status of unit off,
long press "MODE" and "WiFi" buttons simultaneously for 1s,
remote controller will send WIFI reset code and then the WIFI
function will be turned on. WIFI function is defaulted OFF after
energization of the remote controller.
NOTICE:
● This function is applicable to partial of models.
15.
QUIET
button
Press this button, the Quiet status is under the Auto Quiet mode
(display " " and "AUTO" signal ) and Quiet mode (display "
" signal) and Quiet OFF (there is no signal of " " displayed).
After powered on, the Quiet OFF is defaulted.
Under the Quiet mode (Display " " signal).
NOTICE:
● This function is applicable to partial of models.
To Next Page
Loading...
