GreenWorks 25012 - User Manual

Questions and Answers

A
Allen ThompsonAug 13, 2025
What to do if my GreenWorks 25012 is not starting?
- A
  Alexander CarterAug 13, 2025
  If your GreenWorks Lawn Mower isn't starting, there are several potential causes: * The extension cord might not be properly connected to the mower plug. Ensure it's securely reconnected, using the cord retainer to keep it close to the motor/blade control. * The extension cord may not be connected to a power source. Verify it's plugged into a live 120V AC, 60 HZ AC receptacle. * The circuit breaker on the mower might have tripped. Try pushing it to reset. * The motor control switch could be defective. In this case, have it replaced by an authorized service center.
A
Aaron RiosAug 16, 2025
Why is my GreenWorks 25012 not mulching properly?
- E
  Erin RoblesAug 16, 2025
  If your GreenWorks Lawn Mower isn't mulching properly, it's likely due to wet grass clippings sticking to the underside of the deck. To solve this, wait until the grass dries completely before mowing.
D
david08Aug 20, 2025
Why is my GreenWorks 25012 not starting?
- C
  Carol GuzmanAug 21, 2025
  Your GreenWorks Lawn Mower might not be starting due to several reasons. First, check if the extension cord is properly connected to both the mower plug and a live 120V AC, 60 HZ AC receptacle. Use the cord retainer to keep the cord close to the motor/blade control. Also, check if the circuit breaker on the mower has tripped and, if so, push to reset it. If none of these steps work, the motor control switch may be defective and should be replaced by an authorized service center.
K
Kristin AndersonAug 25, 2025
How to fix GreenWorks Lawn Mower cutting unevenly?
- S
  Scott DickersonAug 25, 2025
  Uneven cutting with your GreenWorks Lawn Mower can often be attributed to a rough or uneven lawn surface, or an improperly set cutting height. To resolve this, move the wheels to a higher position, ensuring all wheels are at the same cutting height to promote even cutting.
S
stoneaaronAug 28, 2025
How to improve mulching with GreenWorks Lawn Mower?
- V
  Veronica McintyreAug 28, 2025
  If your GreenWorks Lawn Mower is not mulching properly, it is likely due to wet grass clippings sticking to the underside of the deck. Wait until the grass dries before mowing to improve mulching performance.
D
Dana NewtonAug 31, 2025
Why is my GreenWorks Lawn Mower vibrating at a higher speed?
- P
  patelanitaAug 31, 2025
  If your GreenWorks Lawn Mower is vibrating excessively, it could be due to: * An unbalanced blade. You can balance the blade by grinding each cutting edge equally. * A bent motor shaft. Stop the motor immediately, disconnect the power source, and carefully inspect for any visible damage. Have it repaired by an authorized service center before attempting to restart the mower.
D
Debbie RoseSep 4, 2025
What to do if GreenWorks Lawn Mower is hard to push?
- K
  kari37Sep 4, 2025
  If your GreenWorks Lawn Mower is difficult to push, it could be due to high grass, the rear of the mower housing and blade dragging in heavy grass, or the cutting height being too low. Try raising the cutting height to make it easier to push.
K
Krystal AguilarSep 8, 2025
Why is my GreenWorks 25012 vibrating at higher speed?
- M
  Mr. James Butler MDSep 8, 2025
  If your GreenWorks Lawn Mower is vibrating at a higher speed, it could be due to an unbalanced blade or a bent motor shaft. To address this, first balance the blade by grinding each cutting edge equally. If the vibration persists, stop the motor, disconnect the power source, and inspect for damage. A bent motor shaft should be repaired by an authorized service center before restarting the mower.