Grizzly G0505 User Manual (English)

Other manuals for Grizzly G0505

Owner's Manual40 pages

Instruction Manual35 pages

Questions and Answers:

U
uarnoldAug 12, 2025
How to fix excessive snipe on a Grizzly G0505 Planer?
- L
  Lindsay KimAug 12, 2025
  If your Grizzly Planer produces excessive snipe, resulting in a gouge at the end of the workpiece, it might be due to the outfeed extension wing sloping down or not being level with the table. You can adjust the outfeed extension wing to fix this. Another possible cause is that the workpiece isn't supported as it exits the planer. To remedy this, get assistance or use support accessories to properly support the workpiece.
J
Jennifer GreenAug 16, 2025
Why does my Grizzly Planer leave a consistent chipped pattern?
- J
  Julie JohnsonAug 16, 2025
  If you notice a consistent chipped pattern on your workpiece when using the Grizzly Planer, it could be due to knots or conflicting grain direction in the workpiece. Inspect the workpiece and only use clean stock. Another cause may be a nicked or chipped knife, which would require a knife replacement. Also, ensure that the depth of cut isn't too great; reduce it if necessary.
C
Charles EverettAug 20, 2025
What to do if my Grizzly Planer leaves long lines on the workpiece?
- B
  Brendan Edwards MDAug 20, 2025
  If your Grizzly Planer is leaving long lines or ridges along the workpiece length, it's likely due to a nicked or chipped knife. Replacing the knife should resolve this issue.
G
guy99Aug 25, 2025
Why does my Grizzly G0505 Planer stop during a cut?
- K
  Kim RobinsonAug 25, 2025
  If the workpiece stops or slows in the middle of a cut with your Grizzly Planer, it could be because the depth of cut is too great; try reducing it. Another reason could be dull or damaged knives, so inspect, sharpen, or replace them. Lastly, pitch or glue build-up on the planer components can cause this issue; clean the internal components with a pitch/resin dissolving solvent.
J
jkelleyAug 27, 2025
Why does my Grizzly Planer leave a glossy surface?
- R
  Robin WrightAug 27, 2025
  If your Grizzly Planer is producing a glossy workpiece surface, it could be due to dull knives. Check, sharpen, or replace the knives. Alternatively, the depth of cut might be too shallow, so try slightly increasing it.
J
Jessica BushAug 31, 2025
How to fix uneven knife marks on my Grizzly Planer?
- D
  Dennis HaydenAug 31, 2025
  If you are getting uneven knife marks, a wavy pattern, or chatter marks across the face of your workpiece with the Grizzly Planer, it could be because the knives are not properly installed. Properly adjust the height of the knives. Another potential cause is worn cutterhead bearings, which would need to be checked and possibly replaced.
C
christinekingSep 4, 2025
Why does my Grizzly G0505 Planer leave fuzzy grain?
- J
  Janice WoodsSep 4, 2025
  If your Grizzly Planer is leaving a fuzzy grain on the workpiece, it could be due to excessive moisture in the workpiece. Check the moisture content and allow the wood to dry or season if it's over 20%. Another possible cause is dull knives, which should be checked, sharpened, or replaced.

Grizzly G0505 Specifications

General

Model	G0505
Category	Planer
Voltage	110V/220V
Max. Planing Depth	1/8"
Minimum Stock Thickness	1/4"
Maximum Stock Thickness	6"
Number of Knives	3
Cutterhead Diameter	2-1/2"
Dust Port Size	4"
Motor	2 HP