Grizzly G1028Z Parts Manual

4 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

DUST COLLECTOR

MODEL G1028Z/G1029

INSTRUCTION MANUAL

COPYRIGHT © 1991 BY GRIZZLY IMPORTS, INC.REG # TX 3170576

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY IMPORTS, INC.

REVISED FEBRUARY, 2002. PRINTED IN TAIWAN

PARTS LIST DISCLAIMER

THIS PARTS LIST AND DRAWINGS REPRESENT THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS PRODUCT

IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF THE MACHINE, THIS PARTS LIST MAY NOT DEPICT YOUR MACHINE EXACTLY. CONTACT CUSTOMER

SERVICE IF YOU HAVE ANY QUESTIONS ABOUT PART DIFFERENCES. PREVIOUS PARTS LIST VERSIONS ARE NOT AVAILABLE ONLINE.

Other manuals for Grizzly G1028Z

Owner's Manual40 pages

Questions and Answers:

J
Jorge NealAug 1, 2025
What to do if my Grizzly Dust Collector is making loud noises and vibrating?
- R
  rachelbookerAug 1, 2025
  First, ensure the dust collector is on a flat, stable surface. If it wobbles, stabilize it. Disconnect the dust collector from power and inspect the impeller for damage such as dents, bends, or loose fins; replace the impeller if any damage is found. Also, check that all fasteners on the dust collector are tight. If the impeller is loose on the motor shaft and both are damaged, replace them as a set. Finally, replace the motor fan cover if it is dented.
Q
qsmithAug 6, 2025
Why won't my Grizzly Dust Collector start or why does the breaker trip?
- D
  dallenAug 6, 2025
  A blown fuse in the control box may be the problem; correct any short circuits and replace the fuse. The wall fuse or circuit breaker might be blown or tripped; ensure the circuit size is suitable and replace any weak breakers. Make sure the power supply is switched on and has the correct voltage. Check for broken wires or disconnected/corroded connections and repair/replace them. If the ON button or ON/OFF switch is faulty, replace it. If the motor is at fault, test, repair, or replace it.
K
Kristi Hernandez PhDAug 12, 2025
Why is my Grizzly Dust Collector vibrating or operating noisily?
- D
  Devin HallAug 12, 2025
  A motor or component might be loose; inspect and replace any stripped or damaged bolts/nuts, and retighten them with thread locking fluid. If the motor mount is loose or broken, tighten or replace it. Ensure the machine is correctly mounted and sits evenly; tighten or replace anchor studs if mounted to the floor, or chock the machine casters if it's mobile. If the motor fan is rubbing on the fan cover, replace the dented cover or the loose/damaged fan. Test the motor bearings by rotating the shaft; if there's rotational grinding or a loose shaft, replace the bearings.

Grizzly G1028Z Specifications

General

Intake Hole Diameter	4 in.
Impeller	Balanced Steel
Collection Bag Capacity	5.5 cu. ft.
Base Size	24 in. x 24 in.
Air Flow (CFM)	1700 CFM
Static Pressure (in. SP)	8.5 in. SP
Inlet Size (in.)	4
Dust Capacity (cu. ft.)	5.5 cu. ft.
Height (in.)	80 in.
Width (in.)	24 in.
Depth (in.)	24 in.
Weight (lbs.)	130 lbs.

Related product manuals

Preview: Grizzly G1028

Preview: Grizzly G1163

Preview: Grizzly G1163P

Preview: Grizzly G0785

Preview: Grizzly g0703

Preview: Grizzly G0860

Preview: Grizzly G0710

Preview: Grizzly G0441

Preview: Grizzly G0440

Preview: Grizzly G0548

Preview: Grizzly G0583Z

Preview: Grizzly G0548ZP

Grizzly G0548ZP