Grizzly G1037Z User Manual (English)

Other manuals for Grizzly G1037Z

Instruction Manual52 pages

Machine Data Sheet2 pages

Questions and Answers:

G
Gloria VelasquezAug 21, 2025
What to do if my Grizzly G1037Z motor stalls and the circuit breaker blows?
- R
  Renee MartinezAug 21, 2025
  If your Grizzly Planer's motor stalls, won't start, and the fuses or circuit breakers blow, there are several potential causes: * There may be a short circuit in the line cord or plug. Inspect the cord or plug for damaged insulation and shorted wires. * There may be a short circuit in the motor or loose connections. Inspect all connections on the motor for loose or shorted terminals or worn insulation. * Incorrect fuses or circuit breakers in the power line. Install correct fuses or circuit breakers. * Low voltage. Correct the low voltage conditions. * The motor may be overloaded. Reduce the load on the motor.
J
Justin MorrisAug 23, 2025
Why does my Grizzly G1037Z Planer motor overheat?
- S
  Samuel ValenciaAug 25, 2025
  Your Grizzly Planer motor may overheat due to: * The motor being overloaded. Reduce the load on the motor. * Restricted air circulation through the motor. Clean out the motor to provide normal air circulation.
C
Christopher EscobarAug 26, 2025
What to do if my Grizzly Planer slows down during operation?
- C
  cgallagherAug 26, 2025
  If your Grizzly Planer slows down while operating, consider the following: * The feed rate may be too high. Try feeding the workpiece slower. * The depth of cut may be too great. Reduce the depth of cut. * The knives may be dull. Sharpen the knives.
P
Pamela LeonAug 27, 2025
Why am I getting chipped grain when planing with my Grizzly G1037Z?
- J
  John WallaceAug 27, 2025
  Chipped grain when planing or molding with your Grizzly Planer can occur because: * You are planing against the grain. Flip the board and plane the other side. * The knives are dull. Sharpen or replace the knives.
D
Debbie ScottAug 29, 2025
How to fix a loud noise coming from my Grizzly G1037Z?
- C
  Carla RiveraAug 29, 2025
  A loud, repetitious noise from your Grizzly Planer could be caused by: * Missing or loose pulley setscrews or keys. Inspect keys and setscrews, and replace or tighten if necessary. * The motor fan hitting the cover. Tighten the fan or shim the cover. * A defective V-belt. Replace the V-belt.
K
Keith CardenasSep 1, 2025
What causes fuzzy grain when planing with my Grizzly G1037Z?
- A
  Amy SmithSep 1, 2025
  Fuzzy grain when planing or molding with your Grizzly Planer can be attributed to: * Lumber with high moisture content. If the moisture content is higher than 20%, sticker the lumber and allow it to dry. * Dull knives. Sharpen or replace the knives.
A
Aaron KellySep 3, 2025
How do I control snipe on my Grizzly G1037Z?
- N
  ntorresSep 3, 2025
  If you cannot control snipe on your Grizzly Planer, it may be because long or heavy boards sag as they enter and exit the cutter-head. Lift up on the unsupported end of the board as it enters and exits the cutter-head.
Z
Zachary MartinezSep 5, 2025
What causes chatter marks when planing with my Grizzly G1037Z?
J
James Lucas DVMAug 19, 2025
How to troubleshoot a Grizzly G1037Z when the motor will not start?

Grizzly G1037Z Specifications

General

Type	Benchtop Planer
Cutterhead Speed	10, 000 RPM
Number of Knives	3
Maximum Cutting Height	6 in
Maximum Cutting Depth	1/8"
Feed Rate	26 ft/min
Table Length	24"
Motor	2 HP, 120V, single-phase