Grizzly G1071 User Manual (English)

Other manuals for Grizzly G1071

Owner's Manual40 pages

Instruction Manual26 pages

Machine Data Sheet2 pages

Questions and Answers:

G
Gordon WilliamsJul 25, 2025
What to do if my Grizzly G1071 does not start?
- Y
  Yvonne SmithJul 26, 2025
  If your Grizzly Sander doesn't start or a breaker trips, here's what to check: * Ensure the switch disabling key is installed. * Verify the power supply is on and has the correct voltage. * Test the plug/receptacle for good contacts and correct wiring. * Test or replace the start capacitor if it's faulty. * Correct any miswired motor connections. * Make sure the wall circuit breaker is the correct size and replace it if it's weak. * Check and fix any broken, disconnected, or corroded wires. * Replace the motor ON/OFF switch if it's faulty. * Test, repair, or replace the motor if necessary.
W
wilsonwilliamJul 31, 2025
Why does my Grizzly G1071 stall or is underpowered?
- G
  georgebradleyJul 31, 2025
  If your Grizzly Sander stalls or is underpowered, try the following: * Decrease the feed rate. * Ensure you're only sanding wood with moisture content below 20%. * Correctly wire the motor. * Check the plug/receptacle for good contacts and correct wiring. * Test, repair, or replace the motor bearings. * Clean or replace the sandpaper and reduce the feed rate or sanding depth. * Clean the motor, let it cool, and reduce the workload. * Test, repair, or replace the motor.
A
Andrew BaldwinAug 4, 2025
What to do if Grizzly Sander has excessive vibration or noisy operation?
- M
  Marcus JuarezAug 4, 2025
  If your Grizzly Sander vibrates or operates noisily, check the following: * Inspect and replace any damaged bolts/nuts, and re-tighten them with thread locking fluid if the motor or any component is loose. * Fix or replace the fan cover and replace the fan if the motor fan is rubbing on the fan cover. * Test the motor bearings by rotating the shaft; bearing replacement is required if there's rotational grinding or a loose shaft. * Inspect and repair or replace the gearbox if it's damaged.
A
Amanda LopezAug 9, 2025
Why does my Grizzly G1071 Sander leave deep grooves?
- M
  Melanie SalazarAug 9, 2025
  If your Grizzly Sander is leaving deep sanding grooves or scars on the workpiece, it could be due to several reasons. First, the sanding sleeve might be too coarse for the desired finish, so try using a finer grit sanding sleeve. Second, you might be sanding across the grain; make sure to sand with the grain. Finally, you might be applying too much sanding force; reduce the pressure on the workpiece while sanding.
K
Kristen BanksAug 15, 2025
What to do if sanding surfaces clog quickly on my Grizzly G1071 Sander?
- S
  Shawn PowellAug 15, 2025
  If sanding surfaces clog quickly or burn when using your Grizzly Sander, it could be due to applying too much pressure against the sleeve. Try reducing the pressure on the workpiece while sanding. Alternatively, if you are sanding softwood, consider using a different type of wood. If that's not an option, accept the characteristics of the softwood and plan on cleaning or replacing the sanding sleeves frequently.
M
Matthew MccarthyAug 19, 2025
Why do grains rub off the sanding sleeve of my Grizzly G1071?
- J
  Jeremy MeyerAug 19, 2025
  If grains rub off the sanding sleeve of your Grizzly Sander, it could be because the sanding sleeve has been stored in an incorrect environment. Store sanding sleeves away from extreme temperatures and humidity. It may also be happening because the sanding sleeve has been folded or smashed. Store sanding sleeves separately and not folded or flat.