Growatt MIC TL-X Series User Manual

Installing the Device
Connecting Cables
3.1 Installing the DC Input Power Cable
2. 3 Installing the Monitor
2.2 Installing the Mounting Bracket And MIC TL-X Series
Ensure that the Monitor is installed securely.
Overview
2.
2. 1 Installation Requirements
Tilt and Space
1.
3.
MIC TL-X Series
Quick Guide
Description
A
Inverter
1
B
Mounting bracket
1
C
Quick Guide
1
D
Monitor(Optional)
1
E
1
F
1
G
3
H
2
I
3
Notice：
RJ 45 connector
Before installing the device,check that the pack-
age contents are intact and complete against
the packing list.If any damage is found or any
component missing,contact your dealer.
Object
Quantity
Signal connector
J
PV+/PV- terminal
1/1
K
PV+/PV- metal terminal
1/1
L
AC connector
1
M
Uninstall signal and AC connector tool
1
N
Uninstall PV connector
1
Self-tapping screws
Plastic expansion pipe
Safety-lock screws
The Inverter
Side
Pull the DC input power cable back to ensure that it is connected securely.
The Inverter
Side
Install
Remove
Fix the wall bracket
Installation & Tighten
screw assemblies
The Inverter
Side
The Inverter
Side
The Inverter
Side
The Inverter
Side
Cables
Cables
Positive metal
terminal
Positive connector
Negative connector
Negative metal
termina
4~6mm²
4~6mm²
Drilling holes
3.2 Installing the AC Output Power Cable
3.3 Installing the Signal Cable
3.4 Installing the DRMS Cable
Connect the AC output power cable to the AC connector.
The Inverter
side
The Inverter
side
The Inverter
side
The Inverter
side
The Inverter
side
NO.
1
2
3
NO
4
5
6
REFGEN
COM/DRM0
Notice：
1.When laying out signal cables, separate them from
power cables to avoid strong signal interference
sources.
DRM Port Pin Definitions
COM Port Pin Definitions
DRM5
Definition
Definition
Unclock the housing
No.
Definition
1
2
3
4
NA
CT-P
NA
CT-N
RS 485A1
RS 485B1
This pin is
no signal
Signal for
export
limitation
(optional)
Signal for
communi-
cation
DRM8
DRM7
DRM6
No.
Definition
6
5
7
8
RS 485A2
RS 485B2
Signal for
Smart
Meter
Notice：
Suggest using 4mm²cables. Ensure the exposed core wire is totally inserted into the cable hole and connected securely.
Type 1 Type 2
185
12

Growatt MIC TL-X Series Specifications

General

Output Voltage	230 V
AC Voltage Range	180 V - 280 V
THDi	< 3 %
DC Switch	Yes
Protection Degree	IP65
Frequency	50 Hz / 60 Hz
Communication Interfaces	Ethernet, RS485
Power Factor	0.8 leading - 0.8 lagging
Operating Temperature Range	-25 °C ... +60 °C
Cooling Method	Natural Cooling

Summary

Overview of MIC TL-X Series

Installing the MIC TL-X Series Device

Installation Requirements

Specifies tilt and space requirements for device installation.

Mounting Bracket Installation

Instructions for installing the mounting bracket for the MIC TL-X Series.

Monitor Installation

Guidance on ensuring the monitor is installed securely.

Connecting Cables for MIC TL-X Series

DC Input Power Cable Connection

Steps for installing the DC input power cable.

AC Output Power Cable Connection

Instructions for connecting the AC output power cable.

Signal Cable Installation

Procedure for installing the signal cable.

DRMS Cable Installation

Steps for installing the DRMS cable.

Connecting Meters to Inverter

EASTRON Meter Connection

Details on connecting the EASTRON SDM230-Modbus meter to the inverter.

CHINT Meter Connection

Details on connecting the CHINT DDSU666 meter to the inverter.

Verifying the Installation

Powering On the System

System Power On Controls

Describes touch button functions for system power on and navigation.

Export Limitation Setting