Name: Growatt MOD 11KTL3-X
Brand: Growatt
Rating: 4 (1 reviews)

To Next Page

To Previous Page

13.3 System error

Error code

Description

Suggest

Error 200

AFCI Fault

1.After shutdown,Check the panel terminal.

2.Restart inverter.

3.If error message still exists,contact manufacturer.

Error 201

Leakage c u r re nt

too high.

1.Restart inverter.

2.If error message still exists,contact manufacturer.

Error 202

The DC input

voltage is

exceeding the

maximum

tolerable value.

1.Immediately disconnect the DC switch and check the

voltage

2.If the fault code still exists after the normal voltage is

restored, contact manufacturer

Error 203

PV isolation Low

1.After shutdown, check whether the panel shell is

reliably grounded.

2.If error message still exists,contact manufacturer.

Error 300

AC V Outrange

1.Check grid voltage.

2.If the error message still exists despite the grid voltage

being within the tolerable range, contact

manufacturer.

Error 301

AC terminals

reversed

1.Check AC terminals

2.If error message still exists,contact manufacturer.

Error 302

No AC Connection

1.After shutdown,Check AC wiring.

2.If error message still exists,contact manufacturer.

Error 303

NE abnormal

1.Check PE,to ensure that the PE line contact good.

2.If error message still exisits,contact Manufacturer.

Error 304

AC F Outrange

1.Restart inverter.

2.If error message still exists,contact manufacturer.

Error 305

Over Load Fault

1.Check whether output load over range; If load too

large, please reduce load

2.If error message still exists, contact manufacturer.

Error 306

CT LN Reversed

1.After shutdown Check the SP-CT connection.

2.If error message still exists,contact manufacturer.

Error 307

C o m m u n i c a t i o n

f a u l t , M 3 d i d n ' t

receive SP-CT data

1.Check communication wire

2.If error message still exists,contact manufacturer.

Error 308

C o m m u n i c a t i o n

fault;Pairing time

too long

1.Restart pairing

2.If error message still exists,contact manufacturer.

Error code

Description

Suggest

Error 400

DCI bias abnormal

1.Restart inverter

2.If error message still exists, contact manufacturer.

Error 401

DC Voltage High

Fault

1.Restart inverter.

2.If error message still exists,contact manufacturer.

Error 402

Output DC current

too high.

1.Restart inverter.

2.If error message still exists,contact manufacturer.

Error 403

O u t p u t c u r r e n t

unbalance

1.After shutdown,Check the output current is not

balanced.

2. If the error message still exists, contact manufacturer

Error 404

bus sample fault

1.Restart inverter.

2.If error message still exists,contact manufacturer.

Error 405

Relay fault

1.Restart inverter.

2.If error message still exists,contact manufacturer.

Error 406

Init model fault

1.Reset mode

2.If error message still exists,contact manufacturer.

Error 407

AutoTest failure

1.Restart inverter.

2.If error message still exists,contact manufacturer.

Error 408

NTC Temperature

too high

1.After shutdown,Check the temperature, normal restart

the inverter

2. If the error message still exists, contact manufacturer

Error 409

Bus voltage

abnormal

1.Restart inverter.

2.If error message still exists,contact manufacturer.

Error 410

C o m m u n i c a t i o n

board and control

p a n e l s a m p l i n g

battery voltage is

inconsistent

1.Restart inverter

2.If error message still exists, contact manufacturer.

Error 411

Communication

fault

1.After shutdown,Check communication board wiring

2. If the error message still exists, contact manufacturer

Error 412

Temperature

sensor connection

is abnormal

1.After shutdown,Check the temperature sampling

module is connected properly

2.If the error message still exists, contact manufacturer

Other manuals for Growatt MOD 11KTL3-X

Manual180 pages

Questions and Answers:

Need help?

Do you have a question about the Growatt MOD 11KTL3-X and is the answer not in the manual?

Growatt MOD 11KTL3-X Specifications

General

Product type	-
Maximum power	11000 W
Output current	18.3 A
Output frequency	50/60 Hz
MPP voltage range	140 - 1000 V
Number of strings per MPPT	1
Output power capacity (max)	11 kVA
Input operation voltage (max)	1100 V
Input operation voltage (min)	160 V
Maximum input current per MPPT	13 A
Output operation voltage (max)	440 V
Output operation voltage (min)	340 V
Total Harmonic Distortion (THD)	3 %
Number of maximum power point tracking (MPPT)	2
Operating temperature (T-T)	-25 - 60 °C
Built-in display	Yes
Display technology	OLED
Product color	White
Overvoltage category	CAT II
Power protection features	Over voltage, Short circuit
International Protection (IP) code	IP66