Growatt SPH 8000TL3 BH User Manual

Installation
Operation Manual
&
Shenzhen Growatt New Energy Technology CO.,LTD
No.28 Guangming Road, Shiyan Street, Bao’an District,
Shenzhen, P.R.China
No.28 Guangming Road, Shiyan Street, Bao’an District,
Shenzhen, P.R.China
GR-UM-158 A-00-GR-UM-158 A-00-
+86 0755 2747 1942 +86 0755 2747 1942
www.ginverter.comwww.ginverter.com
T
E
W
service@ginverter.comservice@ginverter.com
Download
Manual
Growatt New Energy

Growatt SPH 8000TL3 BH Specifications

General

Model	SPH 8000TL3 BH
Category	Inverter
Manufacturer	Growatt
Max. DC Voltage	1000 V
Max. AC Output Power	8000 W
Max. DC Power	12000 W
Nominal DC Voltage	620 V
Number of DC Inputs	2
Number of MPP Trackers	2
Nominal AC Power	8000 W
Max. AC Power	8000 W
Nominal AC Frequency	50 / 60 Hz
THDi	<3%
Euro Efficiency	97.5%
DC Switch	Yes
Protection Degree	IP65
Operating Temperature Range	-25°C to +60°C
Cooling Method	Natural cooling
Max. Charging/Discharging Power	8000 W
MPPT Voltage Range	200 - 850 V
Nominal AC Voltage	230 V
AC Voltage Range	180 V - 280 V / 310 V - 480 V
Power Factor	0.8 leading to 0.8 lagging
Communication	RS485, WiFi, GPRS, Ethernet

Summary

1 Brief Introduction

1.4 Safety Instructions

Essential safety guidelines for installation and operation.

2 Safety

2.2 Safety Measure

Critical safety measures and warnings for operation.

4 Unpacking and inspection

5.1 Basic installation requirements

Essential criteria for selecting an installation location and environment.

5 Installation

5.2 Installation requires tools and RJ 45 terminal sequence of the LAN line.

Tools and wiring steps for LAN cable installation.

5.3 Installation Instructions

5.3.1 Attention Layout (length of sensors consider)

5.3.2 Installation of SPH

Step-by-step guide for mounting the SPH inverter on the wall.

5.4 SPH System Connection Mode

5.4.1 Connection of PV terminal

Detailed steps for connecting PV input terminals.

5.4.2 Connection of AC terminal and off grid terminal

5.4.3 Connection of battery terminal

5.4.10 Grounding connection

6 Commissioning

6.1 Commissioning of SPH

Step-by-step guide for initial system commissioning.

6.2 Operation modes

Explanation of different operating modes for the SPH inverter.

6.2.1 Normal mode

6.2.2 Fault mode

6.2.6 Shutdown mode

6.3 Country setting

6.3.1 Switch to country table

6.4.4 work mode set up

Basic Parameter Setup

Backup Mode Setup

Priority Setup

Mode Change Setup

Export Limit Setup

6.5 Communication

6.5.1 Use of USB-A port

6.5.2 Use of RS232 port

6.5.3 The SPH's monitoring

7 Start-up and shut down SPH system

7.1 Start-up the SPH system

Step-by-step guide for starting up the SPH system.

7.2 Disconnect the SPH system

Procedure for safely shutting down and disconnecting the SPH system.

8 Attention of the installation environment, maintenance and cleaning

9 Fault removal

9.1 System fault information list and troubleshooting suggestions

Troubleshooting common system errors and fault messages.