Growatt SPH 10000TL3 BH User Manual

Installation
Operation Manual
&
Shenzhen Growatt New Energy Technology CO.,LTD
No.28 Guangming Road, Shiyan Street, Bao’an District,
Shenzhen, P.R.China
No.28 Guangming Road, Shiyan Street, Bao’an District,
Shenzhen, P.R.China
GR-UM-158 A-00-GR-UM-158 A-00-
+86 0755 2747 1942 +86 0755 2747 1942
www.ginverter.comwww.ginverter.com
T
E
W
service@ginverter.comservice@ginverter.com
Download
Manual
Growatt New Energy

Growatt SPH 10000TL3 BH Specifications

General

Model	SPH 10000TL3 BH
Category	Inverter
Max. DC Voltage	1000 V
Nominal DC Voltage	600 V
Number of MPPTs	2
Nominal AC Output Power	10000 W
AC Nominal Voltage	230 V / 400 V
Frequency	50/60 Hz
Total Harmonic Distortion (THD)	<3%
DC Connection Type	MC4
Protection Degree	IP65
Topology	Transformerless
Operating Temperature Range	-25°C to +60°C
Noise Level	<30 dB
Cooling Method	Natural Convection
MPPT Voltage Range	200 V - 950 V
Max. AC Output Power	11000 VA
AC Voltage Range	180-280V
Humidity	0 to 100% (Non-condensing)
Power Factor	>0.99 (Adjustable 0.8 leading - 0.8 lagging)

Summary

2 Safety

2.2 Safety Measure

Details essential safety precautions for handling high voltage and equipment.

2.3 Symbols introduction on the SPH inverter

5 Installation

5.1 Basic installation requirements

Specifies location, materials, and environmental conditions for SPH installation.

5.2 Installation requires tools and RJ 45 terminal sequence of the LAN line.

Lists required tools and explains the LAN line wiring sequence.

5.3 Installation Instructions

Step-by-step guide for physically mounting the SPH inverter on a wall.

5.4.1 Connection of PV terminal

Instructions for connecting the PV input terminals using MC4 connectors.

5.4.2 Connection of AC terminal and off grid terminal

Details connecting AC output and off-grid terminals for grid/backup power.

5.4.3 Connection of battery terminal

Guide for connecting the battery terminals using MC4 connectors.

5.4.4 Connection of meter terminal

Instructions for connecting the meter terminal for energy flow monitoring.

5.4.5 Connection of communication terminal for lithium battery (CAN)

5.4.6 Connection of RS 485 (reserved) terminal

5.4.7 Connection of DRMS terminal (Australia only)

5.4.8 Connection of temperature probe for lead-acid battery

5.4.9 Connection of Dry contact

5.4.10 Grounding connection

Details grounding requirements for the SPH inverter.

6 Commissioning

6.1 Commissioning of SPH

Steps for electrifying and commissioning the SPH inverter after installation.

6.2 Operation modes

Explains the different operating modes of the SPH inverter.

6.2.1 Normal mode

Details the normal operation states including online and backup modes.

6.2.2 Fault mode

Describes how the SPH handles and displays system or machine faults.

6.2.6 Shutdown mode

6.3 Country setting

6.3.1 Switch to country table

6.4.4 work mode set up

Guide to configuring various operating modes of the SPH inverter.

6.5 Communication

7 Start-up and shut down SPH system

7.1 Start-up the SPH system

Step-by-step guide to starting up the SPH inverter.

7.2 Disconnect the SPH system

Procedure for safely disconnecting and shutting down the SPH system.

8 Attention of the installation environment, maintenance and cleaning

8 Attention of the installation environment, maintenance and cleaning

9 Fault removal

9.1 System fault information list and troubleshooting suggestions

Lists common error messages and their suggested solutions.

11 Decommissioning

11.1 Dismantling the energy storage

12 Product specification

12.1 Growatt SPH series energy storage machine product specification

14 Contact

14 Contact