Hach MET ONE 3400 - Assemble the Particle Counter System

48 pages

To Next Page

To Previous Page

Assemble the particle counter system

Figure 4 shows the setup of the particle counter system.

Figure 4 Particle counter assembly

14 English

Main Page

Table of Contents3
Specifications7
Instrument Specifications7
Sample Measurement Specifications8
Battery Specifications8
General Information8
Safety Information9
Use of Hazard Information9
Precautionary Labels9
Compliance10
Country-Specific Approval for Wi-Fi Devices10
Certification11
General Product Information11
Installation11
Unpack the Instrument11
Wiring Safety Information12
Electrostatic Discharge (ESD) Considerations12
Electrical Connections13
Install the Batteries14
Assemble the Particle Counter System16
Install the Printer Paper17
Connect RS485 Communication17
Network and Communications19
About Network and Communications Setup19
Setup for Serial Communication19
Setup for Ethernet Communication19
Setup for Wireless Communication19
Set Wireless Security20
Particle Counter Navigation20
Configuration21
About Configuration21
About Basic and Advanced Operation21
Set the Operation Mode at Initial Startup21
Change the Operation Mode21
Configure the System22
Set the Time and Date22
Set the Sleep Mode and Backlight Timeout22
Set the Alarm Reasons Option22
Set the Sample Comments Option23
Set the User Interface Language23
Manage Units and Alarms23
Manage Audible Alarm Settings24
Set the Measurement Units24
Set the Flow Rate Alarm Values24
Add an Alarm Reason24
Edit an Alarm Reason24
Delete an Alarm Reason24
Apply an Alarm Reason to a Data Record25
Set the Inert Gas and Altitude Values25
Set the Particle Count Alert (Beep Function)25
Change the Relative Humidity and Temperature Probe25
Manage Backup and Restore Settings26
Make a Backup of Configurable Settings26
Restore Settings from Backup26
Configurations26
Copy a Configuration26
Install a Configuration26
Locations, Areas and Groups27
Location Management27
Add a Location27
Edit a Location27
Configure New Settings for the Location27
Copy Settings from Another Location28
Set Location Alarms28
Remove a Location28
Change the Order of Locations28
Area Management29
Add a New Area29
Edit an Area29
Remove an Area29
Change the Order of Areas29
Group Management29
Add a Group29
Install a Group29
Delete a Group30
Add a Location to a Group30
Sizes Function30
Data Management30
Store Partial Data30
Manage the Data Buffer30
Set the Data Buffer to Rotate Data30
Set the Data Buffer Size31
Real-Time PDF/CSV Option31
Turn on the PDF Option31
Save the Count Data to a Folder31
Manage Users and Permissions32
Enable the User Logon Function32
Log on as Administrator32
Change the Password32
Replace a Forgotten Password32
Add a User33
Assign Groups to a User33
Assign User Access Rights33
Operation34
Log on to the Particle Counter34
Measure Particle Counts34
Change the Particle Count Location34
See Settings During the Particle Count34
See Historical Data During the Particle Count34
Use the Filter Scan Probe35
Manage Sample Batch Identification35
Enter or Change a Batch ID35
Disable a Batch ID35
Set or Clear the Batch ID35
How to Use the Test and Report Wizard35
About Standard Sampling Protocols35
About Reports36
Set up the Test and Report Wizard36
Start Sample Measurement with the Wizard36
Use Existing Data37
Report Test Results37
How to Use the Print Center37
About the Print Center37
Print Records Manually37
Set Automatic Print Functions39
Review Historical Buffer Data39
Set the Data Filter39
Clear the Data Buffer39
Export Data39
About Status Values in Exported Data40
Configure and Enable the FTP Function41
Data Transfer to the OPC Server41
User-Initiated Data Upload41
User-Initiated Data Download41
Automatic Data Download41
Maintenance42
Clean the Instrument Exterior42
Set the Count to Zero42
Update the Instrument Software42
Charge the Batteries in the Particle Counter42
Battery Recharge Intervals43
Calibrate the Battery43
Diagnostics and Troubleshooting43
Factory Settings44
Parts and Accessories44
Parts for the 28.3 LPM Counter (3413 and 3415)44
Parts for the 50 LPM Counter (3423 and 3425)44
Parts for the 100 LPM Counter (3445)45
3400 Series Parts45
Spare Parts Kit (2087919-01)46

Hach MET ONE 3400 - Assemble the Particle Counter System

Table of Contents

Related product manuals