EasyManuals Logo

hager EZN002 User Manual

hager EZN002
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Werkingsdiagram
IN: bediening
OUT: uitgang
Verklaring van het knipperen van de LED:
- uitgangsrelais open, tijdinstelling niet
geactiveerd
- uitgangsrelais open, tijdinstelling
geactiveerd
- uitgangsrelais gesloten, geen
tijdinstelling geactiveerd
- uitgangsrelais gesloten, tijdinstelling
geactiveerd.
Working diagram
IN: control
OUT: output
Reason of the LED flashing:
- output relay open, time delay inactive
- output relay open, time delay active
- output relay closed, time delay inactive
- output relay closed, time delay active.
Funktionsdiagramm
IN: Steuerung
OUT: Ausgangzustand
Funktionsanzeige durch LED:
- Ausgang im Ruhezustand, kein
Zeitablauf
- Ausgang im Ruhezustand, Zeit läuft
- Ausgang im Arbeitszustand, kein
Zeitablauf
- Ausgang im Arbeitszustand, Zeit läuft.
Diagramme de fonctionnement
IN : commande
OUT : sortie
Signification du clignotement de la LED :
- relais de sortie ouvert, pas de
temporisation en cours
- relais de sortie ouvert, temporisation en
cours
- relais de sortie fermé, pas de
temporisation en cours
- relais de sortie fermé, temporisation en
cours.
1 6E 6502.c
6E 6502.c
A2
1
816
A1
15
2
4
6
8
10
1
0,1s
1s
0,1mn
1mn
0,
1h
1h
E
ZN002
EZN002
¢
£
§
ß
®
©
T
IN
(B1)
OUT
(15 - 18)
LED
1 2 3
2
4
6
8
10
1
0,
1
s
1s
0
,1mn
1mn
0,1h
1h
EZN002
0,1s
1s
0,1mn
1mn
0,1h
1h
2
4
6
8
10
1
LED
L / +
N / -
18
A1
16
15
A2 B1
16
18
IN
15
4
EZN002
Pouvoir de coupure min. :
100 mA / 12 V
Température de fonctionnement :
-10 °C... +50 °C
Température de stockage :
-20 °C... +70 °C
Capacité de raccordement :
souple : 1
...6
rigide : 1,5
...10
Raccordement électrique
alimentation en 12 à 230 V
12 à 48 V
Nota : n’est pas destiné à être connecté à un
circuit d’alimentation de sécurité à très basse
tension (TBTS).
Spécifications techniques
Alimentation :
entre A1 et A2 : 12 à 230 V +10% -10%
12 à 48 V +10% -10%
Tension de commande : idem alimentation
Fréquence : 50/60 Hz
Sortie : 1 inverseur libre de potentiel
Pouvoir de coupure max. :
AC1 : 8 A / 230 V 50 000 cycles
Incandescence : 450 W 50 000 cycles
Fluo non compensé : 600 W 50 000 cycles
Charge inductive cos
φ
0,6 : 5 A 100 000 cycles.
Minimale Schaltleistung:
100 mA / 12 V
Umgebungstemperatur:
-10 °C... +50 °C
Lagerungstemperatur:
-20 °C... +70 °C
Anschlußkapazität:
mehdrähtig: 1
...6
eindrätig: 1,5
...10
Elektrischer Anschluß
Spannung von 12 bis 230 V
12 bis 48 V
Anmerkung: nicht geeignet zum Anschluss
an Sicherheitkleinspannungskreise (SELV).
Technische Daten
Versorgungsspannung:
zwischen A1 und A2: 12 bis 230 V +10% -10%
12 bis 48 V +10% -10%
Steuerspannung: gleich Verzorgungsspannung
Frequenz: 50/60 Hz
Ausgang: 1 Wechsler potentialfrei
Schaltleistung:
AC1: 8 A / 230 V 50 000 Zyklen
Glühlampen: 450 W 50 000 Zyklen
Leuchtstofflampen: 600 W 50 000 Zyklen
Induktive Last cos
φ
0,6: 5 A 100 000 Zyklen.
Min. breaking capacity:
100 mA / 12 V
Working temperature:
-10 °C... +50 °C
Storage temperature:
-20 °C... +70 °C
Connection capacity:
flexible: 1
...6
rigid: 1,5
...10
Electrical connection
supply from 12 to 230 V
12 to 48 V
Note: not suitable to be connected to a safety
extra low voltage (SELV) circuit.
Technical specifications
Supply:
between A1 and A2: 12 to 230 V +10% -10%
12 to 48 V +10% -10%
Control voltage: identical to the supply
Frequency: 50/60 Hz
Output: 1 volt free changeover contact
Max. capacity:
AC1: switching 8 A / 230 V 50 000 cycles
Incandescent lights: 450 W 50 000 cycles
Non compensated fluorescent: 600 W 50 000 cycles
Inductive load cos
φ
0,6: 5 A 100 000 cycles.
FR
DE
GB
Réglage de la temporisation
De 0,1 s. à 10 h.
réglage de la gamme de temporisation
réglage fin de la temporisation
La position du sélecteur
multipliée par la valeur
indiquée par le potentiomètre
= temporisation T.
Exemple : T = 0,1 min. x 7 (0,1 min. = 6 s.)
T = 6 s. x 7 = 42 s.
Notice d’instructions
Relais temporisé
retardé au
déclenchement
Bedienungsanleitung
Rückfallverzögertes
Zeitrelais
User instructions
Delay OFF timer
Einstellung der Verzögerungszeit
Von 0,1 s. bis 10 h.
Einstellung des Verzögerungsbereiches
Feineinstellung der Verzögerungszeit
Die Position des Verzögerungswahlschalters
multipliziert mit der Potentiometer-einstellung
= Verzögerungszeit T.
Beispiel: T = 0,1 Min. x 7 (0,1 Min. = 6 s.)
T = 6 s. x 7 = 42 s.
Time delay setting
From 0,1 s. to 10 h.
time setting
multiple of time setting
The position of the selector
multiplied by the
value indicated on the potentiometer
gives the
value of the delay T.
Example: T = 0.1 min. x 7 (0.1 min. = 6 s.)
T = 6 s. x 7 = 42 s.
Gebruiksaanwijzing
Min. scheidingsvermogen:
100 mA / 12 V
Werkingstemperatuur:
-10 °C... +50 °C
Stockagetemperatuur:
-20 °C... +70 °C
Ansluiting:
soepele: 1
...6
stijve: 1,5
...10
Elektrische aansluiting
voeding 12 tot 230 V
12 tot 48 V
Nota: mag niet aangesloten worden op een
veiligheidsvoedingskring met zeer lage
spanning (ZLVS).
Technische specificaties
Voeding:
tussen A1 en A2: 12 tot 230 V +10% -10%
12 tot 48 V +10% -10%
Frequentie: 50/60 Hz
Uitgang: 1 omschakelaar vrij van potentieel
Max. scheidingsvermogen:
AC1: 8 A / 230 V 50 000 cyclussen
Gloeilamp: 450 W 50 000 cyclussen
Fluo niet gecompenseerd: 600 W 50 000 cyclussen
Inductieve belasting cos
φ
0,6: 5 A 100 000
cyclussen.
Tijdvertragende relais
bij afschakeling
Regeling van de tijdinstelling
Van 0,1 s. tot 10 u.
regeling van het gamma van tijdinstelling
fijnregeling van de tijdinstelling
De stand van de keuzeschakelaar
vermenigvul-
digd met de door de potentiometer aangegeven
waarde
= tijdinstelling T.
Voorbeeld: T = 0,1 Min. x 7 (0,1 Min. = 6 s.)
T = 6 s. x 7 = 42 s.
NL
http://waterheatertimer.org/Hagar-timers-and-manuals.html

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the hager EZN002 and is the answer not in the manual?

hager EZN002 Specifications

General IconGeneral
Quantity1

Related product manuals