To Next PageTo Next PageWhy are clothes grayed or yellowed after using my Haier XQG65-11SU Washer/Dryer?
Clothes can become grayed or yellowed after washing in your Haier Washer/Dryer if you're not using enough detergent for large loads. Try adding more detergent to the load.
Why is my Haier Washer vibrating so much during spinning?
Excessive vibration during spinning in your Haier Washer may occur if some packing bolts haven't been removed. Another reason might be that the washing machine is positioned on an uneven surface.
What to do if my Haier Washer won't drain?
If your Haier Washer is not draining, check if the drain hose is blocked. Also, verify that the drain hose end is less than 100cm above the floor level.
What to do if my Haier XQG65-11SU does not operate?
If your Haier Washer/Dryer isn't working, here are a few things to check: * Make sure the unit is plugged in securely. * Verify the electrical wall receptacle has the correct voltage. * Check the circuit breaker and replace the fuse if needed. * Ensure the unit isn't in 'Off' mode and the door is properly closed. * Confirm the control knob is set correctly. * Avoid overloading the washer, redistribute clothes if necessary. * Note that the washer pauses in some cycles, which is normal.
Why is my Haier XQG65-11SU making noise?
If your Haier Washer/Dryer is making noise, it could be due to several reasons: 1. The washer may need to be reinstalled. Refer to the washer installation section. 2. The washer load may need re-balancing because it is uneven. 3. Coins, loose change, buttons, or other heavy objects could be the source of the noise. Consult the Operating Guide for normal operating sounds. 4. A squealing sound may indicate an overloaded wash tub. 5. Vibration noise can occur if the washer isn't level on the floor or if clothes are unevenly distributed in the tub.
Why is there static after using my Haier XQG65-11SU?
Static after using your Haier Washer/Dryer is often caused by over-drying. Try adjusting for a shorter drying time. Mixing synthetic fabrics, sorting and separating different fabrics, or using a fabric softener can also help.
Why are my clothes ripped in my Haier XQG65-11SU?
Clothes can get ripped or develop holes in your Haier Washer/Dryer due to sharp objects left in pockets, such as pins and belt buckles. Remove any small, loose sharp objects and fasten belts, zippers, and metal snaps before washing. Also, check if you are using undiluted bleach and avoid adding it directly to the wash.
How to fix incorrect water temperature in my Haier Washer/Dryer?
If the water temperature is incorrect in your Haier Washer/Dryer, check your water heater temperature. Also, ensure that the inlet hoses are properly connected (hot to hot & cold to cold).
What to do if my Haier Washer/Dryer has soap residue?
If you notice soap residue on your clothes after washing in your Haier Washer/Dryer, the detergent may not be dissolving properly in the water. Try checking the water temperature or adding the detergent as the wash tub is being filled with water, before loading your clothes.
Why is my Haier Dryer working but not drying the clothes?
If your Haier dryer is running but your clothes aren't drying, consider these possibilities: * The unit may be overloaded; the dryer drum should only be half full. * The lint trap might be full; ensure it is clean and dust-free. * The dryer load may need to be resorted, separating heavy clothes from regular ones. * Bulky clothes may require repositioning during the cycle. * If clothes dry unevenly, a higher dry setting may be needed, or the clothes may need to be resorted.
General| Model | XQG65-11SU |
|---|---|
| Type | Washer/Dryer |
| Capacity | 6.5 kg |
| Spin Speed | 1100 RPM |
| Energy Efficiency Class | A+++ |
| Noise Level (Washing) | 58 dB |
| Loading type | Front-loading |
| Dimensions (W x D x H) | 600 x 600 x 850 mm |
| Dimensions (H x W x D) | 850 x 600 x 600 mm |
Detailed identification and explanation of the washer's external components and controls.
Guide to using power, cycle selectors, load levels, and specific wash cycle descriptions.
Understanding water temperature settings and operating the clothes dryer function.
Instructions for cleaning lint trap, button trap, casters, and general cabinet care.
Guidance on moving, storing the appliance, and resolving common operational issues.
List of tools and accessories needed for the appliance installation.
Steps for removing packing materials, shipping bolts, and leveling the washer.
Instructions for connecting water inlet hoses and the drain hose to the appliance.
Guidance on proper electrical hookup, grounding, and unit dimensions.
