Hama DIR3200SBT - Connection Via Headphone Jack; Connection Via USB Interface; 16 System Settings; Equaliser

20
16.2 Internet settings
16.2.1 Network wizard – Configuration of Internet
connection / Search
The network wizard helps you set up a connection
between the radio and the Internet. More methods
of conguration and detailed information are amplied
subsequently.
• You can start the Network wizard as follows:
• Press [
] (7) to go to the system settings.
•
Use [POWER/VOL
UME/ENTER/NA
VIGA
TE] (11)
to navigate to the "Internet settings" menu item.
• Conrm the selection by pressing [POWER/VOLUME/
ENTER/NAVIGATE] (11).
• Use [POWER/VOLUME/ENTER/NAVIGATE] (11)
to navigate to the "Network wizard" menu item.
• When the wizard is started, the radio searches for WLAN
(WiFi) connections and then shows a list of the available
networks.
• Turn [POWER/VOLUME/ENTER/NAVIGATE] (11) to
switch between the networks found. At the bottom of
the list are options to restart the search ("[Rescan]") or
congure the connection yourself ("[Manual cong]").
• If your network is not found or the SSID (Service Set
Identication, that is, the name of your network) is
not shown, the network may be hidden or out of range.
In this case, try manual conguration.
16.2.2 Wireless network connection (WLAN)
Depending on the network, there are a number of ways
to connect to it.
Networks that support connection via WPS (Wi-Fi Protected
Setup) are identied in the list with the prex "[WPS...]".
Other connections are either open networks or connections
protected with a PSK, or Pre-Shared-Key.
WPS/PSK/open network connection
WPS allows simple and nevertheless protected connection
of the radio to the network. Two options are available
for this purpose:
The connection can be set up by means of PBC, or Push-
Button Conguration, or by the PIN procedure, in which
the web interface of your router prompts you to enter
a randomly generated sequence of numbers.
PBC setup
• Select your desired network. (Indicated by the prex
"[WPS...]")
• In the WPS menu, then select the "Push Button"
option and conrm the selection by pressing [POWER/
VOLUME/ENTER/NAVIGATE] (11).
• Press the WPS button on your router or current access point.
This can often be done using the web interface, as well.
• Consult the operating instructions of your router or
access point for details.
• Once the process has been started on the router or
access point, the radio should be able to nd and
connect to the network.
• Alternatively, PBC setup can be initiated from the radio's
Internet settings:
• Press [
] (7) to go to the system settings.
• Use [POWER/VOLUME/ENTER/NAVIGATE] (11) to
navigate to the "Internet settings" menu item.
• Conrm the selection by pressing [POWER/VOLUME/
ENTER/NAVIGATE] (11).
• Use [POWER/VOLUME/ENTER/NAVIGATE] (11) to
navigate to the "PBC Wlan setup" menu item.
PIN setup
• Select your desired network. (Indicated by the prex
"[WPS...]")
• In the WPS menu, choose the PIN option and conrm
your selection by pressing [POWER/VOLUME/ENTER/
NAVIGATE] (11).
• The radio generates an 8-digit code, which must be
entered into the web or user interface of your router or
access point.
• Consult the corresponding handbook for details on
conguring the router or access point.
Skip WPS/Pre-Shared Key (PSK) conguration
• Choose the item "Skip WPS" to proceed to key entry.
• On networks that do not support WPS, you will go directly
to key entry.
• In the input screen, enter the whole key and then conrm
with the OK button.
• If the key was entered correctly, the radio connects to
the access point and establishes the Internet/network
connection.