Page 6 <&(%$*4.8"4,7%H'*#$"&8#I%/7*,#*%4,77%JKLLLKLMMKNOPO1 Item 56825
?@<6AQ D@CEA6E@ER6S@?CR%T6GUCEV T6GUCEV%ACW?SETUP?@<6AQ D@CEA6E@ER6S@?CR%T6GUCEV T6GUCEV%ACW?SETUP
V(&'89"83
AX%W;6!6EA%6G6RA;CR%?BXR[%@EU%U6@AB%%
<;XD%CERX;;6RA%V;XFEUCEV%TC;6%RXEE6RACXE-%
R.*4Y%)"$.%,%H',7"2"*9%*7*4$("4",8%"2%>&'%,(*%"8%9&'+$%,#%$&%).*$.*(%$.*%&'$7*$%"#%
/(&/*(7>%3(&'89*91%%%
U&%8&$%'#*%$.*%)*79*(%"2%$.*%/&)*(%4&(9%&(%/7'3%"#%9,5,3*91%%C2%9,5,3*9I%.,Z*%"$%(*/,"(*9%+>%,%#*(Z"4*%
2,4"7"$>%+*2&(*%'#*1%%C2%$.*%/7'3%)"77%8&$%2"$%$.*%&'$7*$I%.,Z*%,%/(&/*(%&'$7*$%"8#$,77*9%+>%,%H',7"2"*9%*7*4$("4",8I%
9&%8&$%'#*%,9,/$*(%/7'3#1
1. The green wire inside the cord is connected to
the grounding system in the welder. The green
wire in the cord must be the only wire connected
to the welder’s grounding system and must never
be attached to an electrically “live” terminal.
Never leave the grounding wire disconnected
or modify the Power Cord Plug in any way.
2. Make sure the tool is connected to an outlet having
the same configuration as the plug. If the tool must
be reconnected for use on a different type of electric
circuit, the reconnection should be made by qualified
service personnel; and after reconnection, the tool
should comply with all local codes and ordinances.
B"3.%<(*H'*84>%V(&'89"83
1. The Welder has internal grounding, there
is no need to ground the Welder.
2. The metal work bench must be properly grounded
in accordance with all relevant electrical codes
and standards before operation. Have the work
bench grounded by a qualified electrician
if you are not qualified to do so.
3. To ground the work bench, connect a #12 AWG
grounding wire (not included) from the work
bench to a grounding rod (not included).
The grounding rod must be an earth-driven
copper or brass rod (electrode) which can
adequately ground the work bench.
4. Refer to local regulations for
ground source information.
B"3.%<(*H'*84>%;,9",$"&8
1. The operator of welding equipment that causes
harmful interference to radio services shall promptly
take appropriate measures to correct the problem.
2. If the operator of welding equipment is notified
by the FCC that operation of such equipment is
endangering the functioning of a radio navigation
or safety service, the operator shall immediately
cease operating the equipment. Operation may
be resumed on a temporary basis only for the
purpose of eliminating the harmful interference.
Operation may be resumed on a regular basis
only after the harmful interference has been
eliminated and approval from the FCC obtained.
3. When notified by the FCC that a particular
installation is causing harmful interference, the
operator or manufacturer shall arrange for an
engineer skilled in techniques of interference
measurement and control to make an investigation
to ensure that the harmful interference has
been eliminated. The Regional Director may
require the engineer making the investigation
to furnish proof of his or her qualifications.
6]$*8#"&8%R&(9#
U&%8&$%'#*%,8%*]$*8#"&8%4&(9%&8%$."#%)*79*(1
;*/7,4*5*8$%R&(9#
1. F#*%&87>%&8*%&2%$.*%#'//7"*9%/&)*(%4&(9#%2&(%
$."#%)*79*(%&(%,8%"9*8$"4,7%(*/7,4*5*8$%4&(91
2. U&%8&$%"8#$,77%,%$."88*(%&(%7&83*(%
4&(9%&8%$."#%)*79*(1
3. U&%8&$%/,$4.%4&(9#%&2%,8>%7*83$.%
$&3*$.*(%2&(%$."#%"$*51%%W,$4.*#%5,>%,77&)%
5&"#$'(*%$&%/*8*$(,$*%$.*%"8#'7,$"&8I%
(*#'7$"83%"8%*7*4$("4%#.&4Y1
To Next Page
Loading...
