Harman Kardon AVR 161 User Manual (English)

Other manuals for Harman Kardon AVR 161

Questions and Answers:

S
santiagomichaelAug 12, 2025
What to do if Harman Kardon Receiver has front-panel display lights, but there’s no sound or picture?
- A
  Alexandra SaundersAug 13, 2025
  If the front-panel display lights up on your Harman Kardon Receiver but you're not getting any sound or picture, here are a few things to check: * Make sure all input and speaker connections are secure. * Ensure that the mute button is not activated by pressing it. * Verify that the volume control isn't turned down; increase the volume.
H
Haley NunezAug 16, 2025
How to troubleshoot a Harman Kardon AVR 161 Receiver that does not function?
- K
  kathleenmayoAug 16, 2025
  If your Harman Kardon Receiver isn't functioning, start by ensuring that the power cord is properly plugged into a working AC power outlet. Also, check if the AC outlet is switch-controlled.
J
Jodi McintyreAug 20, 2025
Why Harman Kardon Receiver does not respond to remote control commands?
- C
  Christopher GarciaAug 20, 2025
  If your Harman Kardon Receiver isn't responding to the remote control, try these steps: 1. Replace the batteries in the remote. 2. Make sure there's a clear line of sight between the remote and the receiver's front-panel remote sensor.
C
Christopher BentonAug 25, 2025
What to do if there is no sound from any speaker connected to Harman Kardon AVR 161?
- J
  jacksonericAug 25, 2025
  If you're not getting any sound from any speaker connected to your Harman Kardon Receiver, it could be in protection mode. This might be due to a short circuit. Check all speaker wires at both the speaker and AVR connections for any crossed wires. If that doesn't solve the issue, the amplifier may have internal problems, and you should contact your local Harman Kardon service center.
P
Patrick PowellAug 27, 2025
Why is there no sound from center or surround speakers on my Harman Kardon Receiver?
- R
  Richard WeaverAug 27, 2025
  If you're not hearing sound from the center or surround speakers on your Harman Kardon Receiver, consider the following: * Ensure you've selected a surround mode other than stereo. * Be aware that monophonic programs do not contain surround information. * Verify the speaker configuration in the setup menu. * Understand that stereo program material may not always generate center or surround channel information.
T
Trevor KnightAug 31, 2025
What to do if remote buttons light, but Harman Kardon AVR does not respond?
- K
  Kelli BushAug 31, 2025
  If the remote buttons light up but your Harman Kardon AVR isn't responding, the remote might be in Zone 2 mode. Try pressing the Zone 2 button; it won't illuminate when the remote is in Zone 1 control mode.
C
Christopher MartinezSep 4, 2025
Why is there intermittent buzzing in tuner of my Harman Kardon AVR 161 Receiver?
- T
  Tara BrownSep 4, 2025
  If you're experiencing intermittent buzzing in the tuner of your Harman Kardon Receiver, it could be due to local interference. Try moving the AVR or antenna away from computers, fluorescent lights, motors, or other electrical appliances.
J
Julie ThompsonSep 8, 2025
How to fix surround-back speaker settings that cannot be accessed on Harman Kardon AVR 1710/AVR 171?
- D
  David SmithSep 8, 2025
  If you cannot access surround-back speaker settings and the test tone doesn't play through the surround back speakers on your Harman Kardon AVR 1710/AVR 171, it may be because multi-zone operation has been selected or assigned AMP channels have been assigned to Zone 2. Use the Speaker Setup menu to reassign the Assigned AMP to the surround back left and right channels.

Harman Kardon AVR 161 Specifications

Audio Section

Stereo power	85W per channel, two channels driven @ 6/8 ohms, 20Hz – 20kHz, <0.1% THD
Multichannel power	85W per channel, two channels driven @ 6/8 ohms, 20Hz – 20kHz, <0.1% THD
Input sensitivity/impedance	250mV/27k ohms
Signal-to-noise ratio (IHF-A)	100dB
Surround-system adjacent channel separation - Dolby Pro Logic/DPLII	40dB
Surround-system adjacent channel separation - Dolby Digital	55dB
Surround-system adjacent channel separation - DTS	55dB
Frequency response (@ 1W)	10Hz – 130kHz (+0dB/–3dB)
High instantaneous current capability (HCC)	±29 amps
Slew rate	40V/sec

FM Tuner Section

Frequency range	87.5MHz – 108.0MHz
Usable sensitivity IHF	1.3µV/13.2dBf
Signal-to-noise ratio (mono/stereo)	70dB/68dB
Distortion (mono/stereo)	0.2%/0.3%
Selectivity (±400kHz)	70dB
Image rejection	80dB
IF rejection	80dB

AM Tuner Section

Frequency range	522kHz – 1, 620kHz
Signal-to-noise ratio	38dB
Usable sensitivity (loop)	425µV
Distortion (1kHz, 50% mod)	1.0%
Selectivity (±10kHz)	30dB

Video Section

Television format	PAL
Input level/impedance	1Vp-p/75 ohms
Output level/impedance	1Vp-p/75 ohms
Video frequency response (composite video)	10Hz – 8MHz (–3dB)
HDMI	Supports up to 4K x 2K

General Specifications

Power requirement	220V – 240V AC / 50Hz – 60Hz
Power consumption	<0.5W (standby); 450W maximum
Dimensions (H x W x D)	121mm x 440mm x 300mm (4-3/4" x 17-5/16" x 11-13/16")
Weight	4.6kg (10 lb)

View in Manual