PROGRAMMING THE REMOTE 37
Programming the Remote
Channel Control Punch-Through
The AVR’s remote may be programmed to oper-
ate so that the channel control function for either
the TV, cable or satellite receiver used in your sys-
tem may be used in conjunction with one of the
other devices controlled by the remote. For exam-
ple, while using and controlling the VCR, you
may wish to change channels on a cable box or
satellite receiver without having to change the
device selected by the AVR or the remote. To pro-
gram the remote for Channel Control Punch-
Through, follow these steps:
1. Press the Input Selector button
4
for the
device you wish to have the channel control asso-
ciated with and the Mute button
at the
same time until the red light illuminates under the
Input Selector
4
and the Program/SPL
Indicator
2
flashes amber.
2. Press the Volume Down button
.The
Program/SPL Indicator
2
will stop flashing
and stay amber.
3. Press and release the AVR
5
or Input
Selector button
4
for the device that will be
used to change the channels. The Program/SPL
Indicator
2
will blink green three times and
then go out to confirm the data entry.
Example: To control the channels using your TV
while the remote is set to control the VCR, first
press the VID 1/VCR Input Selector button
4
and the Mute button
at the same time. Next,
release them and press the Volume Down but-
ton
, followed by the VID 2/TV Input
Selector button
4
.
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown in the example
above. However, press the VID 1/VCR Input
Selector in Steps 1 and 3.
Transport Control Punch-Through
The AVR’s remote may be programmed to oper-
ate so that the Transport Control Functions x
(Play, Stop, Fast Forward, Rewind, Pause and
Record) for a VCR, DVD or CD will operate in
conjunction with one of the other devices con-
trolled by the remote. For example, while using
and controlling the TV, you may wish to start or
stop your VCR or DVD without having to change
the device selected by the AVR or the remote. To
program the remote for Transport Control Punch-
Through, follow these steps:
1. Press the Input Selector
4
for the device
you wish to have the channel control associated
with and the Mute button
at the same time
until the red light illuminates, under the Input
Selector
4
and the Program/SPL Indicator
2
flashes amber.
2. Press the Play button x. The Program/SPL
Indicator
2
will stop flashing and stay amber.
3. Press and release the AVR
5
or Input
Selector button
4
for the device that will be
used to change the channels. The Program/SPL
Indicator
2
will blink green three times and
then go out to confirm the data entry.
Example: To control the transport of a CD player
while the remote is set to control the TV, press the
VID 2/TV Input Selector button
4
and the
Mute button
at the same time. Next, release
them and press the Play button x, followed by
the CD Input Selector button
4
.
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown in the example
above. However, press the VID 2/TV Input
Selector in Steps 1 and 3.
NOTE: Before programming the remote for
Volume, Channel or Transport Punch-Through,
make certain that any programming needed for
the specific TV, CD, DVD, Cable or Satellite
Receivers has been completed.
Resetting the Remote Memory
As you add components to your home-theater
system, occasionally you may wish to totally
reprogram the remote control without the con-
fusion of any commands, macros or ”Punch-
Through“ programming that you may have done.
To do this, it is possible to reset the remote to
the original factory defaults and command codes
by following these steps. Note, however, that
once the remote is reset, all commands or codes
that you have entered will be erased and will
need to be re-entered:
1. Press any of the Input Selector buttons
4
and the ”O“ button
H
at the same time until
the Program/SPL Indicator
2
begins to flash
amber.
2. Press the ”3“ button
H
three times.
3. The red LED under the Input Selector
4
will
go out and the Program/SPL Indicator
2
will
stop flashing and turn green.
4. The Program/SPL Indicator
2
will remain
green until the remote is reset. Note that this may
take a while, depending on how many commands
are in the memory and need to be erased.
5. When the Program/SPL Indicator
2
goes
out, the remote has been reset to the factory
settings.
To Next Page
Loading...
