AVR100
To correct this problem, first unplug the unit from the AC wall outlet and
wait at least three minutes. After the pause, reconnect the AC power
cord and check the unit’s operation. If the system still malfunctions, a
system reset may clear the problem. To clear the AVR 100’s entire
system, first turn the unit off by pressing and releasing the Main Power
Switch so that it pops out from its normal recessed position. Next, press
and hold the CD and Vid 2 buttons while pushing in the Main Power
Switch to turn the unit back on.
AVR110
To correct this problem, first unplug the unit from the AC wall outlet and
wait at least three minutes. After the pause, reconnect the AC power
cord and check the unit’s operation. If the system still malfunctions, a
system reset may clear the problem. To clear the AVR 110’s entire
system, first put the unit in Standby by pressing the System Power
Control button. Next, press and hold the Tone Mode and the FM Mode
Selector buttons for three seconds. The unit will turn on automatically
and display the RESET message in the Main Information Display.
AVR120
To correct this problem, first unplug the unit from the AC wall outlet and
wait at least three minutes. After the pause, reconnect the AC power
cord and check the unit’s operation. If the system still malfunctions, a
system reset may clear the problem. To clear the AVR 120’s entire
system, first put the unit in Standby by pressing the System Power
Control button. Next, press and hold the Tone Mode and the FM Mode
Selector buttons for three seconds. The unit will turn on automatically
and display the RESET message in the Main Information Display
AVR125
To correct this problem, first unplug the unit from the AC wall outlet and
wait at least three minutes. After the pause, reconnect the AC power
cord and check the unit’s operation. If the system still malfunctions, a
system “reset” may clear the problem. To clear the AVR 125’s entire
system, first put the unit in Standby by pressing the System Power
Control Button. Next, press and hold the Tone Mode button for
three seconds. The unit will turn on automatically and display the RESET
message in the Main Information Display
AVR130
To correct this problem, first unplug the unit from the AC wall outlet and
wait at least three minutes. After the pause, reconnect the AC power
cord and check the unit’s operation. If the system still malfunctions, a
system “reset” may clear the problem. To clear the AVR 130’s entire
system memory , first put the unit in Standby by pressing the
Standby/On Switch so that the Power Indicator turns amber. Next,
press and hold the Tone Mode Button for three seconds. The unit will
reset and then turn on automatically.
AVR210
To correct this problem, first unplug the unit from the AC wall outlet and
wait at least three minutes. After the pause, reconnect the AC power
cord and check the unit’s operation. If the system still malfunctions, a
system reset may clear the problem. To clear the AVR 210’s entire
system, first put the unit in Standby by pressing the System Power
Control button. Next, press and hold the Tone Mode and the FM Mode
Selector buttons for three seconds. The unit will turn on automatically
and display the RESET message in the Main Information Display
AVR220
To correct this problem, first unplug the unit from the AC wall outlet and
wait at least three minutes. After the pause, reconnect the AC power
cord and check the unit’s operation. If the system still malfunctions, a
system reset may clear the problem. To clear the AVR 220’s entire
system, first put the unit in Standby by pressing the System Power
Control button. Next, press and hold the Tone Mode and the FM Mode
Selector buttons for three seconds. The unit will turn on automatically
and display the RESET message in the Main Information Display
AVR225
To correct this problem, first unplug the unit from the AC wall outlet and
wait at least three minutes. After the pause, reconnect the AC power
cord and check the unit’s operation. If the system still malfunctions, a
system “reset” may clear the problem. To clear the AVR 225’s entire
system, first put the unit in Standby by pressing the System Power
Control Button. Next, press and hold the Tone Mode button for
three seconds. The unit will turn on automatically and display the RESET
message in the Main Information Display
To Next Page
Loading...
