What does 'Drive Error! AC voltage too high' mean on my Hayward EcoStar SP3400VSP?
This error indicates that the line voltage has risen above 264 VAC, causing the pump to stop. Verify that the line voltage is within 10% of the pump's rated voltage.
How to troubleshoot a Hayward EcoStar SP3400VSP Water Pump motor that will not start?
First, ensure the terminal board connections match the wiring diagram located on the pump data plate label. Next, verify the pump is wired for the correct available field supply voltage (230VAC). Check for any loose or improper wiring connections, open switches or relays, tripped circuit breakers, or blown fuses and correct them. Finally, manually inspect the motor shaft rotation for any obstructions and ensure it moves freely.
What to do if my Hayward EcoStar SP3400VSP Water Pump won't prime?
If your Hayward Water Pump won't prime: * Ensure the pump/strainer housing is filled with water and the cover o-ring is clean. * Make sure the o-ring is properly seated in the cover o-ring groove and lubricated with “Jack’s 327” to create a tighter seal. Ensure the strainer cover is locked firmly in position. * Tighten any loose pipe/union connections on the suction side. * Tighten, repair, or replace leaking O-rings or packing glands on valves. * Remove any debris from the strainer basket or skimmer basket, refill the strainer housing with water, and tighten the cover.
How to fix a noisy Hayward Water Pump?
A noisy Hayward Water Pump can be caused by several factors. Check for air leaks in the suction piping or cavitations due to a restricted or undersized suction line, or a leak at any joint. Low water level in pool, and unrestricted discharge return lines can also cause noise. Correct the suction condition or throttle return lines, if practical. Also, ensure the pump is mounted on a level surface and securely fastened to the equipment pad to prevent vibration. Clean the pump housing to remove any foreign matter. Lastly, noisy motor bearings may require seal replacement.
What to do if my Hayward EcoStar SP3400VSP motor shuts off?
If your Hayward Water Pump motor shuts off, check for low voltage or power drop at the motor, which is frequently caused by undersized wiring. Contact a qualified professional to verify the electrical connections.
What causes a Hayward EcoStar SP3400VSP Water Pump motor to hum but not start?
If your Hayward Water Pump motor hums but doesn't start, the impeller might be jammed with debris. Have a qualified repair professional open the pump and remove the debris.
What does 'Drive Error! Prime failed' mean on my Hayward Water Pump?
This error indicates that the pump was unable to prime within 15 minutes of startup. Check the plumbing and fittings for potential air leaks and correct them.
What does 'Drive Error! Heatsink overheated' mean on my Hayward Water Pump?
This error indicates that the heatsink of the drive has become overheated. Check the motor airflow path for obstructions and clear them. The pump will restart automatically once the temperature reaches an acceptable limit.
What does 'Drive Error! AC voltage too low' mean on my Hayward Water Pump?
This error indicates that the line voltage has dropped below 185 VAC, causing the pump to stop. Verify that the line voltage is within 10% of the pump's rated voltage.
What does 'Drive Error! PFC Circuit Low' mean on my Hayward Water Pump?
This error indicates that the internal drive voltage is too low. Verify that line voltage is within 10% of the pump rated voltage.
Covers general safety, electrical, entrapment, pressure, fire, burn, and installation hazards.
Details electrical specs, voltage, grounding, bonding, and wiring procedures.
Steps for preparing, priming, and starting the pump for operation.
Addresses motor start/operation issues, pump priming, and suction problems.
Solutions for low flow, noisy pump, and understanding drive error codes.
General| Model | EcoStar SP3400VSP |
|---|---|
| Type | Variable Speed Pump |
| Horsepower | 3.0 HP |
| Voltage | 230V |
| Energy Efficiency | Energy Star Certified |
| Warranty | 3 years |
| Control | Digital |
| Motor Type | Permanent Magnet |
| Speed Settings | Programmable |
To Next Page
