To Next PageTo Next Page
Need help?Do you have a question about the Hearth & Home DV3732SBI and is the answer not in the manual?
General| Model | DV3732SBI |
|---|---|
| Category | Indoor Fireplace |
| Type | Direct Vent Gas Fireplace |
| Fuel Type | Natural Gas or Propane |
| Vent Type | Direct Vent |
| Finish | Black |
| Warranty | Limited Lifetime |
| Ignition Type | Electronic |
| BTU Range | 26, 000 - 40, 000 BTU/h |
| Efficiency | 75% |
| Viewing Area | 32" x 20" |
Details appliance certifications and standards compliance.
Specifies requirements for tempered glass used in the appliance.
Lists the British Thermal Unit (BTU) ratings for different models.
Provides guidance for installations at higher elevations.
Defines materials that do not ignite or burn.
Defines materials that can ignite and burn.
Outlines electrical code requirements for installation.
Details specific installation requirements for Massachusetts.
Covers essential safety precautions for operating the gas fireplace.
Introduces the fireplace and its basic operation.
Instructions for adding and operating an optional fan kit.
Guidelines for installing decorative doors and fronts.
Specifies required clearance zones around the fireplace.
Refers to section for details on the fixed glass assembly.
Instructions for operating controls.
Pre-lighting checks and procedures.
Step-by-step guide for lighting the Intermittent Pilot Ignition system.
Step-by-step guide for lighting the standing pilot system.
Procedures to follow after the fireplace has been lit.
Addresses common issues and their solutions.
Tasks homeowners can perform for regular maintenance.
Tasks requiring a qualified service technician.
Illustrates the typical components of the appliance system.
Key factors to consider before installation.
Lists necessary tools and materials for installation.
Procedures for checking the appliance upon arrival.
Guidance on choosing a suitable location for the appliance.
Instructions for building a chase for the appliance.
Specifies required clearances to combustible materials.
Details clearances for mantels and wall projections.
Specifies minimum clearances for vent termination.
Lists approved venting pipe types.
Explains abbreviations used in vent tables.
Guidance on using elbows in vent configurations.
Explains measurement standards for vent pipe.
Instructions for using flexible vent pipe.
Visual representations of vent configurations.
Specifies clearances for vent pipes to combustible materials.
Instructions for framing wall penetrations for vent systems.
Details framing for non-combustible wall penetrations.
Procedures for installing ceiling firestops.
Instructions for installing attic insulation shields.
Preparation steps for top venting configuration.
Preparation steps for rear venting configuration.
Instructions for properly securing and leveling the unit.
Instructions for assembling DVP vent pipe sections.
Instructions for assembling SLP vent pipe sections.
Procedures for assembling slip sections of vent pipe.
Methods for supporting and securing vent pipe sections.
How to take apart vent pipe sections.
Installing decorative components for SLP venting.
Instructions for installing metal roof flashing.
Steps for assembling and installing the storm collar.
Procedures for installing the vertical termination cap.
Installing decorative components for SLP venting.
Specifies heat shield requirements for horizontal vents.
Instructions for installing horizontal termination caps.
Information on converting between fuel types.
Details required gas pressures for operation.
Instructions for connecting the gas supply.
Guidance for installations at high altitudes.
General electrical wiring guidelines.
Wiring specifics for Intellifire ignition systems.
Wiring specifics for standing pilot ignition systems.
Requirements for optional electrical accessories.
Instructions for installing and removing the splatter guard.
Details clearances for mantels and wall projections.
Guidelines for applying facing materials.
Information on compatible doors and finishing material thickness.
Information on hearth systems and their effect on dimensions.
Instructions for removing shipping materials.
How to clean the appliance.
Guidelines for installing approved accessories.
Instructions for placing lava rock and embers.
Step-by-step guide for installing the log set.
Instructions for removing the fixed glass assembly.
Instructions for installing the fixed glass assembly.
Instructions for installing the appliance hood.
How to adjust air shutter settings.
Troubleshooting guide for the standing pilot system.
Troubleshooting guide for the Intellifire ignition system.
Diagram showing appliance dimensions.
Diagrams of various vent components.
List of available service parts with numbers.
Information for contacting the manufacturer.
