Heathkit IO-4205 - Page 16

Page 14
The steps performed in this Pictorial are
in this area of the circuit board. --~---~.....:;
178: 200 .n (Red-Blk-Brn).
168: 330
.n (Org-Org-Brn).
1278: 1800
.n (1.8 k). 1% (Brn-
Gry-Blk-Brn).
' /4 ~
1158: 510 .n (Grn-Brn-Brn).
1148: 220
.n (Red-Red-Brn).
Solder the
leads to the foil and cut
off the excess
lead lengths .
17
A: 200 .n (Red-Blk-Brn).
R116A: 330
!l (Org-Org-Brn).
NOTE:
When a bar e wire is called for in
a step, remove all the insu l ation from
the specified l ength of brown wire.
0
1" bare wire.
R125A: 432
.0 , 1% (Yel-Org-Red-
Blk).
R126A: 432
.0, 1% (Yel-Org-Red-
Blk).
R115A: 510
.n (Grn-Brn-Brn).
R114A: 220
.n (Red-Red -B rn).
R113A: 220
!l (Red-Red-Brn).
Sol
der the leads to the foil and cut
off the excess lead lengths.
y.
Yo
:y.
1 (I N C H IE S)
2
I 1( 8 I 3~ 8 I
~ ( 8 I
1; 8 1
I
I
I
I I
I
I
I
I
I
I
iif l jiill)
0
.e
1
( CM ) 2
3
4
e
I
I
I
I
I
I
I
I
I
8
7
I
IDENTIFICATION
DRAWING
PART
NUMBER
c=:>
r-----l
I I
: I
I I
I I
I I
I
I
I
I
I
PICTORIAL 1-3
3
4
I
I
I
I
I
I
I
I I
I
I
I
I
I I
I
I
I
I
8
"
10
,
12
CONTINUEO
IDENTIFIC
DRAWl
I
I
NOTE: When a wire is called for in a
step,
cut the brown wire to the
specified length. Then remove 1/4" of
insulation from each end.
5
I
2-1/4" Brn wire .
D104B: 1N4149
diode (#56-56).
D103B: 1N4149
diode (#56-56).
R118B: 2700
!l (Red-Viol-Red).
R126B: 432
.0, 1% (Yel-Org-Red-
Blk).
R125B: 432
.0 , 1% (Yel-Org -R ed-
Blk).
R124B:
10
!l (Brn-Blk-Blk).
R127 A: 1800
.n (1.8 k). 1% (B rn -
Gry-Blk-Brn).
' /'1 ~
R123A: 1800 !l (1 .8 k), 1% (Brn-
Gry-Blk-Brn).
'/~ ~
Sol der the leads to the foil and cut
the excess lead lengths.
R122A: 2700
!l (Red-Viol-Red).
R136A: 470
.n (Yel-Viol-Brn).
nP , n r n<> r the l eads to the foil and cut
off
the excess lead lengths.
6
I
I
I I
I
I
I
I I I
I
I I
I
I
I
I I
13 14 18 18
17
7
I