To Next PageTo Next PageHow to get more heat from Heatilator Indoor Fireplace?
To get more heat from your Heatilator Indoor Fireplace, make larger fires if you're using insufficient fuel. Also, burn seasoned wood, which has been covered on top, split, and stacked for 9 months to 2 years. If you are turning the blower on too early or setting it too high, wait until the fire is established and leave it on a lower speed. If there is no blower, add one if available.
Why do I smell smoke in the house when using my Heatilator Indoor Fireplace?
If you smell smoke in the house during operation of your Heatilator Indoor Fireplace, open the damper fully. If needed, check and clean the chimney. Use adequate kindling and fuel. Open glass doors or a window, and check if you need a balanced air make-up. Ensure the fire is built farther back and avoid using exhaust fans during startup. Also, check if a balanced air make-up system is needed.
What to do if Heatilator Indoor Fireplace burns wood too fast?
If your Heatilator Indoor Fireplace burns wood too fast, add glass doors to slow air intake. If the wood is extremely dry, mix in less seasoned wood after the fire is established.
Why does my Heatilator Indoor Fireplace smell like smoke after a fire?
If you smell smoke in the house after you’ve had a fire in your Heatilator Indoor Fireplace, close the damper at the end of the burn if there is a down draft or negative pressure. Check if you need glass doors, a balanced air make-up system, or to raise the chimney. If there is no creosote odor, but the damper was closed too early, wait until the fire is completely out before closing the damper.
General| Fuel Type | Natural Gas or Propane |
|---|---|
| Vent Type | Direct Vent |
| Ignition Type | Electronic Ignition |
| Log Set Material | Ceramic Fiber |
| Efficiency | Up to 70% |
| Control Type | Remote Control |
Details the fireplace system's certification by Underwriters Laboratories Inc. for US installation.
Covers building codes, location planning, vent system, gas, electrical, and accessories.
Explains negative pressure causes and how to minimize its effects on fireplace operation.
Illustrates and lists the main components of the Heatilator fireplace system.
Lists essential tools and building supplies required for fireplace installation.
Instructions for checking fireplace and components for damage before installation.
Discusses options for fireplace placement and considerations for performance.
Specifies minimum clearances to combustibles for safe installation around the fireplace.
Details clearances for combustible side walls and decorative surrounds.
Provides a diagram and instructions for framing the fireplace using lumber.
Guidelines for building a chase structure to enclose the fireplace and vent system.
Lists minimum and maximum heights and lengths for chimney components.
Instructions for installing the outside air kit to supply combustion air.
Guidance on positioning and securing the fireplace to a flat surface.
Step-by-step instructions for installing the refractory panels and hearth stone.
Instructions for installing metal strips to protect the floor from sparks and heat.
Steps to ensure the fireplace is level and square for proper door fit.
Details vertical distances and component selection for chimney height.
Guide to determining chimney components for bypassing obstructions using offsets.
Instructions for connecting chimney sections and ensuring proper engagement.
Steps for cutting, framing, and installing ceiling firestops for safety.
Guidance on installing insulation shields where insulation contacts the chimney.
Procedure for verifying secure connections of chimney sections.
Methods for locking chimney sections and securing them to framing.
Requirements for chimney termination caps, placement, and clearances above the roof.
Instructions for installing a metal chase top to seal the chase around the chimney.
Steps for installing various types of termination caps and their required overlaps.
Guidelines for installing certified gas log sets, including input limits and safety codes.
Requirements for hearth extensions, including R-value, materials, and dimensions.
Defines combustible and non-combustible materials and sealant requirements.
Specifies clearances and limitations for combustible mantels above the fireplace.
Details clearances for combustible side walls and decorative surrounds.
Information on using approved glass doors and referring to their specific manuals.
Emphasizes safe operation, fire supervision, and annual inspections.
Explains the importance of outside air for combustion and its control.
Specifies minimum clearance for room furnishings and combustible materials.
Instructions for operating the flue damper and its importance for draft.
Guidelines for using the firescreen to control sparks during operation.
Best practices for operating glass doors for efficient fireplace use.
Requirement to use the factory-installed integral grate for proper fire management.
Guidance on selecting and using seasoned firewood for optimal performance.
Step-by-step instructions for safely starting and building a fire.
Explains common venting issues like flue leakage and blockage affecting draft.
Provides diagnostic questions and solutions for fire starting and heating issues.
Safe procedures for storing and disposing of fireplace ashes.
Recommendations for regular chimney inspection and cleaning to prevent fires.
Guidance on inspecting refractory panels for cracks and replacement needs.
A comprehensive checklist for inspecting and maintaining fireplace components.
Actions to take in case of a chimney fire and necessary inspections afterward.
Diagrams and measurements of the fireplace unit for installation planning.
Lists catalog numbers and descriptions for various fireplace parts.
Identifies and illustrates various chimney sections, caps, and accessories.
Exploded parts diagram and list for service and replacement of fireplace components.
Outlines the terms, conditions, exclusions, and duration of the product warranty.
Provides contact details for Hearth & Home Technologies and customer support.
