Heatilator NDV36-IFT User Manual

1
Heatilator • NDV30-IFT, NDV33-IFT, NDV36-IFT, NDV36-IFT-NVR, NDV42-IFT Installation Manual • 2620-980 Rev. C • 8/20
Installation Manual
Installation and Appliance Setup
Models:
NOTICE: DO NOT discard this manual!
This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer’s
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certied kit is used.
• DO NOT store or use gasoline or other am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Leave the building immediately.
- Immediately call your gas supplier from
a neighbor’s phone. Follow the gas sup-
plier’s instructions.
- If you cannot reach your gas supplier, call
the re department.
• Installation and service must be performed
by a qualied installer, service agency, or the
gas supplier.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
NDV30-IFT
NDV30L-IFT
NDV33-IFT
NDV33L-IFT
NDV36-IFT-NVR
NDV36-IFT
NDV36L-IFT
NDV42-IFT
NDV42L-IFT
Decorative barrier front must be ordered separately at
time of appliance purchase. See Section 3.A.
CAUTION! Risk of Fire! DO NOT store instruction manuals inside replace cavity.
High temperatures could cause a re.
INSTALLER: Leave this manual with the appliance, not inside the appliance.
CONSUMER: Retain this manual for future reference. Do not store inside the appliance.
Contact your dealer with questions regarding installation, operation or service.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and must be installed for
the protection of children and other at-risk
individuals.

Heatilator NDV36-IFT Specifications

General

Brand	Heatilator
Model	NDV36-IFT
Category	Indoor Fireplace
Language	English

Summary

Getting Started

Design and Installation Considerations

Determine installation location, vent system, gas supply, electrical, and framing needs.

Framing and Clearances

Appliance Location and Clearances to Combustibles

Specifies required clearances to walls and combustible materials for safe installation.

Constructing the Appliance Chase

Termination Location and Vent Information

Vent Termination Minimum Clearances

Details minimum clearances for vent termination to prevent fire risk.

Vent Terminal Clearances

Provides specific clearance requirements for vent terminals based on location.

Vent Clearances and Framing

Pipe Clearances to Combustibles

Details required air space and clearances for vent pipes to prevent fire.

Wall Penetration Framing/Firestops

Ceiling Firestop/Floor Penetration Framing

Install Attic Insulation Shield

Appliance Preparation

Vent Collar Preparation

Securing and Leveling the Appliance

Procedures for properly positioning, securing, and leveling the appliance.

Venting and Chimneys

Assemble Vent Sections (DVP Pipe Only)

Detailed steps for assembling DVP series vent pipe sections correctly.

Assemble Slip Sections

Secure the Vent Sections

Guidance on supporting vent sections vertically and horizontally to prevent sagging.

Vertical Termination Requirements

Horizontal Termination Requirements

Electrical Information

General Information

Wiring Requirements

Details wiring for the IntelliFire Touch Ignition System, including diagrams.

Gas Information

Fuel Conversion

Gas Pressure

Specifies required gas pressures and warnings related to pressure testing.

Gas Connection

Instructions for connecting the gas supply line to the appliance, including safety precautions.

High Altitude Installations

Finishing

Facing Material

Combustible Mantel and Wall Projections

Specifies minimum vertical and maximum horizontal dimensions for combustible mantels.

Non-combustible Mantel and Wall Projections

Details dimensions for non-combustible mantels and wall projections.

Appliance Setup

Remove the Shipping Materials

Install Burner Mineral Wool

Install Fixed Glass Assembly

Install Decorative Barrier Front

Install the Log Assembly