What to do if the Heinner HDW-FS4505WA++ Dishwasher programme won’t start?
If the Heinner Dishwasher program doesn't start, ensure the plug is connected, check your indoor fuses, verify the water inlet tap is on, confirm the machine door is closed, ensure the machine is switched on using the Power On/Off button, and check that the water inlet filter and machine filters aren't clogged.
Why is my Heinner HDW-FS4505WA++ leaving food waste on dishes?
If there are partial food wastes left on the dishes in your Heinner Dishwasher, it might be due to incorrectly placed dishes, an overly loaded basket, dishes leaning against each other, too little detergent, an unsuitable wash programme, a clogged spray arm or filters, incorrectly fitted filters, or a clogged water drain pump. Ensure dishes are correctly placed, avoid overloading, use enough detergent, select an appropriate wash program, and check for blockages.
What to do if the Heinner Dishwasher leaves water inside after the programme?
If water is left inside the Heinner Dishwasher at the end of the programme, it could be that the water drain hose is clogged or twisted, or the filters are clogged. Also, ensure the program has fully finished.
Why are there whitish stains on my Heinner HDW-FS4505WA++ Dishwasher dishes?
If there are whitish stains on the dishes from your Heinner Dishwasher, it could be due to using too little detergent, a low rinse aid dosage, not using special salt for hard water, a low water softener setting, or a poorly closed salt compartment cap. Consider using more detergent, adjusting the rinse aid dosage, using special salt, adjusting the water softener, and ensuring the salt compartment cap is tightly closed.
How to fix rust stains on dishes from Heinner Dishwasher?
If there are rust stains on the dishes from your Heinner Dishwasher, it may be due to insufficient stainless-steel quality of the dishes, a high salt rate in the wash water, a salt compartment cap that isn't closed well, too much salt spillage during filling, or unhealthy mains grounding. Consider using higher quality dishes, ensuring the salt compartment is properly sealed, and addressing any grounding issues.
Why my Heinner Dishwasher is not drying dishes?
If the dishes won't dry up in your Heinner Dishwasher, it could be due to selecting a program without a drying operation, setting the rinse aid dosage too low, or unloading the dishes too quickly. Try selecting a program with a dry operation, increasing the rinse aid dosage, and allowing the dishes to cool down before unloading.
Why is my Heinner Dishwasher making shaking noises?
If shaking and hitting noises are heard during a wash operation of your Heinner Dishwasher, the dishes may be placed incorrectly, or the spray arm is hitting the dishes. Make sure that the dishes are placed correctly and the spray arm can rotate freely.
What to do if the Heinner HDW-FS4505WA++ Dishwasher stops mid-cycle?
If the Heinner Dishwasher stops during a wash operation, it could be due to a power failure, water inlet failure, or the program being on standby mode.
What to do if the Heinner Dishwasher alarm is active against water overflow?
If the alarm is active against water overflow in your Heinner Dishwasher, power off your machine and close the tap. Then contact the service.
What to do if the Heinner HDW-FS4505WA++ has an error of continuous water input?
If your Heinner Dishwasher shows an error of continuous water input, close the tap and contact the service.
General| Type | Freestanding |
|---|---|
| Capacity | 12 place settings |
| Energy efficiency class | A++ |
| Noise level | 49 dB |
| Number of programs | 6 |
| Dimensions (H x W x D) | 85 x 60 x 60 cm |
Key considerations for safe and correct machine installation.
Guidelines and warnings for using the dishwasher in daily operation.
Procedures and advice for dealing with machine malfunctions.
Guidance on selecting a suitable location and placing the dishwasher correctly.
Instructions for connecting the water inlet hose to the tap.
Instructions for connecting the water outlet hose to the drain.
Details on connecting the dishwasher safely to the power supply.
Troubleshooting steps when the wash program fails to start.
To Next Page