INSTALLATION AND OPERATING INSTRUCTIONS
4211-70 G
Rev. 3
5/9/14
R.D. LD
WARNING
SECTION 3: PLACING OF ROCKS (SEE DIAGRAM #10)
HANGING THE HEATER Using the template provided, drill four 9/64"
holes to fasten the heater to the wall. Install two of the four 1/4" x 1
1/8" hex head lag screws (supplied with the heater) into the upper two
holes. Tighten these screws until their heads are about 1/8" from the
wall surface. The screws must be threaded through the wall into a
framing member or backing board to support the heater weight. Hang
the heater on the two upper screws. Locate the other two ¼" x 1 1/8"
hex head lag screws (supplied with the heater); install them into the
two lower mounting holes. Tighten to lock the heater in place. See
Diagram 1 for the heater location details and the necessary clearances
to combustible materials.
Remove the cover of the PK CB-1 Control Box to gain access to the 4
mounting holes in the back of the box. The control box can be
mounting inside the sauna room on a wall according to Diagram 3. Or it
can be mounted outside the sauna room. Locate the 4 screws 3/16 x
3/4"supplied into the 4 mounting holes. (See Diagram 3)
The rocks supplied with the heater have been chosen to provide the best
heater performance. Use of any other type of rock may void the heaters
warranty. Never operate the heater without rocks in place! Rinse the rocks
with water before placing in the heater. Carefully place the rocks loosely so
that the air can circulate through the heater. Packing the rocks too tightly
may cause the heater high limit switch to trip. The rocks must fully cover the
heating elements. Attach the guard with the screws provided.
Fire sprinkler systems
used inside any sauna
room should be properly
rated for sauna room
temperatures.
Do not pour chlorinated
pool or spa water on
heater.
Excessive water use on
heater may cause
damage and void
warranty.
Do not install a shower
in the sauna room.
Electric Shock Hazard -
High voltage exists
within this equipment.
There are no user
serviceable parts in this
equipment. All
installation and service
to this equipment should
be performed by
qualified licensed
personnel in accordance
with local and national
codes.
Do not construct sauna
room so as to restrict air
flow through the bottom
of the heater.
Packing the rocks too
tightly may cause the
heater high limit switch
to trip.
SECTION 4: ELECTRICAL HOOK-UP
Electrical installation must be made by a licensed electrician in
accordance with the National Electrical Code and local
regulations.
Remove the screws from the CB PK-1 control box to access the
electrical connections. Route the wires through the holes provided
on the bottom of the control box and connect the wires to the
terminal block. To determine the correct wire size, refer to
Diagram 2. Use copper supply wire only, suitable for minimum 90
degrees C. The heater must be grounded! See Diagram 6 for
proper connections.
SECTION 5: TEMPERATURE SENSOR
Page 3
Feed the 17 ft "low voltage" sensor wire from the sensor location to the control box (CB PK-1)
location. Sensor wire must be routed completely separate (as per low voltage electrical
wiring codes) from any wiring carrying over 50 volts. It may be necessary to drill holes to
string the wire through the studs or ceiling joists.
Using a flat tip screwdriver, unsnap sensor cover from sensor. Mount sensor to a
finished wall directly above heater and two (2) inches down from ceiling using two
(2) screws (provided) as shown in Diagrams 1, 3 & 5. Connect wires into CB PK-1
on the 3 pin plug labeled "JT2" of the circuit board.
SECTION 2: MOUNTING OF SAUNA HEATER AND PK-1
To Next Page
Loading...
Need help?
General
